Virginia Regulatory Town Hall

Final Text

highlight

Action:
Motor Vehicle Safety Inspection Rules and Regulations-Summer ...
Stage: Final
 
19VAC30-70-6

19VAC30-70-6. Class IV offenses.

A. Class IV offenses are those violations considered so critically important to the integrity and credibility of the Official Annual Motor Vehicle Inspection Program as to require immediate and severe disciplinary action. Any Class IV offense is grounds for suspension or revocation. The following violations and actions shall be considered a Class IV offense:

1. Loss of driver's license, with the exception of an administrative court-ordered suspension that does not exceed seven days.

2. Obvious usage of either alcohol or drugs by an employee associated with the Annual Motor Vehicle Inspection Program.

3. Loss of inspection stickers through neglect, or subsequent violations of subsection K of 19VAC30-70-10.

4. Improper use of inspection supplies, such as placement on a vehicle that has not been inspected or failure to affix the inspection sticker to the vehicle in its proper location, after inspection.

5. Falsifying inspection receipts or inspection records.

6. Giving false information during an inspection complaint investigation.

7. Performing either an inspection or inspections at a station without authority from the safety officer.

8. The arrest of any person associated with the inspection program for a criminal offense or the institution of civil action of a nature that would tend to immediately reflect upon the integrity and reputation of the Department of State Police may be grounds for an immediate suspension inactive inspector or station status until final court disposition. A finding other than acquittal for any criminal offense or a, civil judgment, or bankruptcy may result in a suspension or revocation of the inspector or station appointment, or both.

9. The use of profanity or verbal abuse by station owners, managers, or safety inspectors toward each other or directed at customers presenting their vehicles for inspection.

10. Illegal use of inspection supplies such as stealing, selling, mailing or giving away, or the attempt thereof.

11. Nonpayment of inspection fees.

12. Conduct displayed by station owners, managers, or safety inspectors that may be rude or discourteous, or the use of profanity or verbal abuse directed at or toward Safety Division Personnel.

13. Failure of any person connected with the inspection program to notify their supervising trooper or Safety Division Area Office within 72 hours of an arrest for a criminal offense or the institution of civil action.

14. Any misuse or falsification of the automated Motor Vehicle Inspection Program (MVIP) system through neglect, or intentionally allowing an assigned password or personal identification number (PIN) to be used by other persons.

15. Willfully obtaining computer services without proper authority from the safety officer.

16. Failure to adequately explain and differentiate, both orally and in writing, to customers what repairs are necessary to pass the safety inspection and those repairs that are only recommended. Each station shall explicitly (not fine print) convey to each customer when his vehicle will be examined beyond the parameters of the state inspection and empower the customer with the ability to decline this service.

17. Allowing a suspended or revoked safety inspector to perform predelivery inspections (PDIs) or have access to inspection supplies, which may be grounds for suspension or revocation of the station appointment and an additional suspension or revocation for the inspector.

B. Disciplinary action for a Class IV offense shall be immediate suspension or revocation. A revocation shall not be less than one year or more than three years. A suspension shall constitute any period of time less than a year and shall not be less than 90 days, unless mitigating circumstances exist. Offenses are cumulative in nature and will remain active for a period of 24 months from the date of the offense. For a subsequent violation within 24 months, the suspension or revocation shall be no less duration than the prior discipline received.

C. In the case of the loss of the driver's license, the suspension shall remain in effect until the driver's license is reinstated and consideration for reinstatement of inspection privileges will be made at that time.

D. In cases concerning nonpayment of fees when the inspection station has been given 15 days to reply to a final notice, the suspension of the affected inspection station shall remain in effect until all inspection fees are paid. Consideration for reinstatement of inspection privileges will be made when all fees are paid. Furthermore, stations that have not paid their processing fee after the 15-day period will not be issued any additional inspection supplies. Supply orders may resume when the inspection fee is paid and the station has been reinstated to an active status.

19VAC30-70-7

19VAC30-70-7. General information.

All suspension or revocation decisions may be appealed. The request must be made in writing to the safety officer within 15 calendar days of receiving the official notice of suspension or revocation.

Any violation under any class of offenses requiring a third suspension within a 24-month period shall be grounds for a revocation. The suspension or revocation period for a subsequent violation requiring suspension or revocation under any class of offenses within a 24-month period shall be twice that of a previous suspension or revocation, unless mitigating circumstances exist. Any violation under any class of offenses requiring a third suspension within a 14-month period shall be grounds for revocation.

For suspension periods of less than six months, inspection stations and safety inspectors will not be required to file an application for reinstatement.

For suspension periods of six months or more, or revocation periods of one to three years, inspection stations must complete the process as set forth for original appointment. Reapplications may be made 60 days prior to the suspension expiration of suspension periods only, not revocations. An inspection station that has its privilege to perform inspections revoked must complete the application process as set forth for original appointments after the expiration of the period of revocation.

Suspended safety Safety inspectors who are suspended for suspension periods of six months or more shall contact the nearest appropriate Safety Division Area Office or supervising trooper to request reinstatement. Safety inspectors who have their privilege to perform inspections revoked must complete the application process for initial certification after the expiration of the period of revocation.

Inspection stations that have their privilege to perform inspections revoked must complete the application process as set forth for original appointments after the expiration of the period of revocation. Safety inspectors who have their privilege to perform inspections revoked must complete the application process for initial certification, after the expiration of the period of revocation.

If during the course of an official investigation, station management voluntarily surrenders the station's inspection supplies, particularly after being cautioned not to do so, the station shall not be eligible for reinstatement for a period of 90 days. This voluntary action shall not be the subject of an appeal.

If during the course of an official investigation, an inspector voluntarily surrenders his inspector inspector's license, particularly after being cautioned not to do so, the inspector shall not be eligible for reinstatement for a period of 90 days. This voluntary action shall not be the subject of an appeal.

19VAC30-70-9

19VAC30-70-9. Examinations for inspector's license Inspector requirements.

A. The Department of State Police administers the written examination for original certification for all inspectors. With few exceptions, recertifications are done at the normal testing sites along with original certification tests.

B. In order for an individual to become a certified safety inspector, the following actions shall be followed:

1. The person shall contact his assigned Safety Division trooper or the local Safety Division Area Office to obtain the following:

a. Mechanics Certification Application, Form SP-170B;

b. Criminal History Record Request, Form SP-167; and

c. Mechanics Application Worksheet.

2. The supervising trooper or Safety Division office personnel should ask some preliminary questions to ensure the applicant is qualified to apply.

3. The applicant shall complete (i) Form SP-170B in its entirety and have it notarized on the back; (ii) Form SP-167, to only include sections "Name Information To Be Searched" and "Affidavit For Release of Information," and have it notarized; and complete (iii) the worksheet with two character references, two mechanical references, places of employment, and qualified automotive training or schools completed.

4. The applicant shall then take the completed application forms to the State Police testing site and present it to the trooper conducting the written examination. Applicants arriving after the designated testing time will not be eligible to participate in the written examination.

5. The trooper will verify the notarizations and check the driver's license for validity and identification of the applicant. If the applicant's driver's license is found to be expired, suspended or revoked, the applicant will be advised and the application will be destroyed. The applicant may reapply once the driver's license has been reissued or reinstated.

6. If the applicant successfully completes the test, the trooper will note at the end of Section I on the Form SP-170B the word "Passed" and the date. The trooper will sign the test and send it to Safety Division Headquarters, Mechanics File Section, for further processing and investigation.

7. The Class A examination will consist of five sections: general information, brakes, suspension, lights, and glass. Each section will contain 20 questions. A minimum score of 75% must be attained for each section and for the practical examination. The Class B and C examinations will consist of 50 questions each. A minimum score of 74 must be attained on the written and practical examination.

8. If the applicant fails the test, it will be noted at the end of Section Ion the Form SP-170B with the word "Failed" and the date.

9. If the applicant desires to test again for the written or practical test, he may do so after 30 days. If the applicant is again unsuccessful in passing the examination or examinations, the trooper shall take the application forms and forward them to Safety Division Headquarters, Mechanics File Section. The applicant may contact his assigned Safety Division trooper or the local Safety Division Area Office after six months to reapply.

C. Recertification.

1. Safety inspectors desiring to renew their inspector's license must participate in the recertification written examination. Inspectors arriving after the designated testing time will not be eligible to participate in the written examination.

2. All safety inspectors will be required to satisfactorily pass the appropriate examination for the license the inspector holds.

3. A safety inspector will not be permitted to perform inspections after the expiration date of his inspector's license.

4. A safety inspector's license shall be valid for a period of three years.

5. All safety inspectors' licenses will display an inspector's VSP number and will no longer display the social security number. The inspector's VSP number will be written on the inspection sticker receipt or displayed on the automated MVIP receipt.

6. Safety inspector testing sites will no longer be included on an inspection bulletin. Testing site information will be updated in the computer system, so that the usual letters going to inspectors to remind them of their upcoming recertification will contain the updated information. All Safety Division Area Offices will also have the updated information.

7. If the safety inspector has any questions about the testing sites, the safety inspector should contact the Safety Division Area Office closest to him. The office numbers are:

Richmond 804-743-2217

Culpeper 540-829-7414

Amherst 434-946-7676

Wytheville 276-228-6220

Suffolk 757-925-2432

Salem 540-387-5437

Fairfax 703-803-2622

D. Reinstatement of safety inspector licenses following a period of suspension or revocation.

1. Once a safety inspector's license has been suspended, regardless of the cause for suspension, no application Form SP-170B is required for reinstatement; however, Form SP-170D and Form SP-167 must be completed.

2. If the inspector is suspended for less than six months, the safety inspector's license will be held at the local Safety Division Area Office and returned upon the expiration of the suspension period. A check will be made with DMV prior to reinstatement.

3. If the inspector's license has been suspended for six months or more, he may request reinstatement 60 days prior to the suspension expiration by contacting the supervising trooper. A check will be made by the supervising trooper with DMV and the Central Criminal Records Exchange. A credit report shall also be reviewed by the supervising trooper prior to reinstatement of the inspector. The inspector's license will be returned after the suspension expiration if still valid.

4. If the suspended inspector's license expires during the suspension period, the inspector may complete the process for inspector recertification as set forth in this section. The trooper administering the test will retain all documentation. The inspector's license will be returned at the end of the suspension period and the appropriate documents forwarded to the Safety Division.

5. Inspectors whose safety inspector's licenses have been revoked must complete the application process for initial certification as set forth in this section.

E. Vo-Tech students who successfully complete the Vocational Automotive Mechanics Course and who are expected to graduate from the program with the required 1,080 hours, and meet the requirements of the Department of State Police, will be certified as safety inspectors.

1. The Vo-Tech instructor will contact his assigned Safety Division trooper or the local Safety Division Area Office by March 15 of each year. The written examination will be scheduled for students who are at least 18 years of age or who will be at least 18 years of age by May 31 of that year.

2. The Safety Division troopers responsible for administering the written examinations at the Vo-Tech Centers will forward sufficient application Form SP-170B for each student to complete prior to the testing date. A Criminal History Record Request (Form SP-167) if the student is at least 18 years of age, must also be completed. The Safety Division trooper will indicate at the top of the Form SP-170B the name of the Vo-Tech school where the examination was given.

3. The trooper will verify the notarizations and check the driver's license for validity and identification of the applicant. If the applicant's driver's license is found to be expired, suspended or revoked, the applicant will be advised and the application will be destroyed. The applicant may re-apply once the driver's license has been reissued or reinstated.

4. If the applicant successfully completes the written examination, the trooper will note at the end of Section I on the Form SP-170B the word "Passed" and the date. The trooper will sign the test and forward it to Safety Division Headquarters, Mechanics File Section, for further processing and investigation. Due to the age of these students, this should be done in a minimal amount of time.

5. If the applicant fails the test, it will be noted at the end of Section I on the Form SP-170B with the word "Failed" and the date.

a. The Safety Division trooper will only administer one written examination at the Vo-Tech Center. Those students who fail the first written examination may retest, but not sooner than 30 days from the date of the last written examination. Those students who fail the first written examination will keep the Form SP-170B in their possession and present it to the Safety Division trooper at the test site prior to taking the second written examination.

b. The second written examination will not be administered to the students prior to the end of the school year. Prior to taking the second written examination, the student shall have completed the Vocational Automotive Mechanics Course and must be employed at an official inspection station. These students will not be required to have completed the one year of practical experience as an automotive mechanic.

c. For those students who pass the second written examination, the Safety Division trooper will forward the student's Form SP-170B to the Safety Division for further processing and investigation. Those students who successfully pass all phases for original certification will then be issued a temporary inspector license by the Safety Division trooper.

d. Students failing the second written examination will not be allowed to test again for six months and must complete the application process as set forth for original certification.

6. The written examination will consist of five sections: general information, brakes, suspension, lights, and glass. Each section will contain 20 questions. A minimum score of 75% must be attained for each section.

7. Those students who successfully complete all phases of the written examination and background checks will then be administered a practical examination. The Vo-Tech instructor who holds a valid Class A Safety Inspector's License will administer the practical "Class A" examination to each student who is expected to graduate from the program. The Safety Division trooper should be on hand to observe at least some of the practical examinations administered by the Vo-Tech instructor to ensure that testing is administered according to Safety Division regulations.

8. Those students who successfully complete all phases for original certification by May 31 will be issued a temporary inspector license by the Safety Division trooper. The Safety Division trooper will then forward the completed temporary inspector license to the Safety Division Headquarters, Mechanics File Section.

a. The Safety Division will mail a permanent inspector's license to the student, provided he is at least 18 years of age by May 31 of that year.

b. The Vo-Tech instructor will be required to contact the Safety Division trooper prior to the end of the school year if any student fails to complete the Vocational Automotive Mechanics Course.

c. Any student who fails to complete the Vocational Automotive Mechanics Course will not be licensed as a certified safety inspector and will be required to complete the application process as set forth for original certification.

9. Those students who will be at least 18 years of age after May 31 of that year and have successfully completed the Vocational Automotive Mechanics Course must contact the Safety Division trooper assigned to the inspection station where they are employed and complete the application process as set forth for original certification. These students will not be required to have completed the one year of practical experience as an automotive mechanic.

A. The inspection of motor vehicles required by this chapter shall be made only by those individuals who are certified and licensed as safety inspectors by the Department of State Police. The procedures outlined in this section are applicable to the processing of applications for initial certification, reclassification of safety inspector's licenses, and reinstatement of suspended or revoked safety inspector's licenses.

B. All certified inspectors shall be at least 18 years of age and meet the following qualifications:

1. A minimum of one year of practical experience as an automotive mechanic or six months of practical experience as an automotive mechanic combined with an additional and separate six months of mirroring a certified state inspector, or

2. Satisfactorily completed a training program in the field of automotive mechanics approved by the Superintendent of State Police.

A person who has met either of the practical experience requirements in repairing motorcycles may be certified to inspect motorcycles only. A person who meets practical experience requirements in repairing trailers may be certified to inspect trailers only.

C. Each mechanic entering the inspection program is required to satisfactorily pass a written and practical examination exhibiting knowledge of the inspection procedures.

D. Each certified inspector shall possess a valid Virginia driver's license with the following exceptions:

1. An inspector who is a resident of an adjoining state holding a valid driver's license in that state and who commutes regularly to work in Virginia; or

2. A member of the armed forces of the United States on active duty, or a dependent thereof, who holds a driver's license from his home state.

E. An inspector whose driver's license is suspended or revoked, including the seven-day administrative suspension for an arrest for driving under the influence (DUI), must immediately notify the station's supervising trooper or the local Safety Division Area Office of the suspension or revocation. The suspension or revocation of an inspector's driver's license shall automatically act as a suspension of his privilege to inspect motor vehicles until such suspension or revocation is terminated, and the reinstatement has been made by the Superintendent of State Police.

F. Each licensed safety inspector must have a valid safety inspector's license in his possession at all times while conducting inspections.

G. Each safety inspector with a valid safety inspector's license need only present such valid license to his new employer to commence participation in the program at a new place of employment. Management of the inspection station is required to notify the Safety Division when a safety inspector begins or ends employment. This notification may be handled by contacting the inspection station's supervising trooper by telephone.

H. In the event the safety inspector's license becomes mutilated, lost, or stolen, the inspector must notify the Department of State Police immediately to request a duplicate using the Safety Inspector Notification Form. All required information shall be printed legibly and completely. An inspector who is not employed, writes "Inactive" in the station name block.

In those cases where notification is being made due to an address change, it is necessary to complete the Safety Inspector Notification Form and submit it to the Safety Division Headquarters. The inspector's information will be updated within the MVIP database by the Inspector Files Clerk.

NOTE: The Safety Inspector Notification Form can be downloaded from the Virginia State Police website under the Vehicle Safety Inspection link.

NOTE: Safety inspector licenses are only generated and distributed for initial certifications, renewals, name changes, and mutilated, lost, or stolen licenses. Inspectors submitting a change of address notification are not issued a new license.

I. An inspector must immediately notify the station's supervising trooper or local Safety Division Area Office of an arrest for a criminal offense or the institution of a civil action.

J. Requirements for safety inspector applicants with a specific learning disability.

1. Applicants must furnish documentation from the particular school division where the applicant was classified as having a learning disability. The specific learning disability must be clearly identified.

2. Once the learning disability has been documented, and if applicable, the applicant will be allowed to test with the written exam being orally presented.

3. The station management, where the applicant is employed or to be employed, must agree to have someone present during the hours the employee is conducting inspections to assist with the reading of the Official Motor Vehicle Safety Inspection Manual when necessary during the initial three-year certification period. If the inspector changes stations within the first three-year period, it is the inspector's responsibility to notify station management of his disability and this requirement.

19VAC30-70-9.1

19VAC30-70-9.1. Official inspection station appointment Inspector certification.

A. These procedures are applicable to the application process for initial appointment, reclassification of appointment, change in ownership, change in name, and reinstatement of the appointment for an official inspection station following a period of suspension or revocation.

For investigations involving changes to the original report, only those areas of inquiry that have changed need to be reported.

For changes in station name, location, and classification only, a narrative report is not required. These requests may be reported on the Form SP-164. This report should include information pertinent to the change. A statement should be included to report verification of information contained in the station's new application for appointment.

1. Any garage or other facility that routinely performs motor vehicle, motorcycle, or trailer repairs may apply to the Department of State Police in writing for appointment as an Official Safety Inspection Station.

a. The Department of State Police will forward an application package to the applicant.

b. The application forms are to be completed and returned to the supervising trooper processing the application within 45 days.

c. The application shall include the names, addresses, email addresses, telephone numbers, dates of birth, and social security numbers for the applicant and each person who will supervise or otherwise participate in the program. Each person will also be required to execute an Authorization for Release of Information Form and a Criminal History Record Request (Form SP-167). When a corporation with other established inspection stations is applying for an additional location, it shall not be necessary for the corporate officers to complete the Form SP-167 or undergo the usual background investigation. In these situations, the Department of State Police is only concerned with the personnel who will be responsible for handling and securing the safety inspection supplies.

2. Each inspection station application will be reviewed and the applicant must meet the following criteria:

a. The facility must have been in business at its present location for a minimum of six months.

(1) This requirement will not apply to a change in location for a previously appointed station.

(2) This requirement will not apply to a repair garage that is an established business and is expanding its mechanical convenience to the general public by the addition of other repair locations.

(3) This requirement will not apply to a business license as a franchised dealer of new vehicles.

b. The facility must perform motor vehicle, motorcycle, or trailer repairs routinely.

c. The station must have on hand or be willing to purchase the necessary equipment as identified by the Department of State Police for performing safety inspections.

d. The station must employ or be willing to employ at least one full-time safety inspector with the appropriate license for the desired station's classification.

e. The facility's physical plant must meet the specific standards for the station classification for which the appointment is required.

3. Each applicant station must undergo a background investigation to determine if the business and associated personnel meet the following minimum criteria:

a. A review of the history of management and all persons employed who will participate in the inspection program must reflect general compliance with all federal, state, and local laws.

b. The character, attitude, knowledge of safety inspection requirements, mechanical ability, and experience of each individual who will perform or supervise safety inspections must be satisfactory.

c. The applicant and all participants must be familiar with and agree to comply with the Official Motor Vehicle Inspection Manual. Each vehicle presented for safety inspection must be inspected in strict compliance with the Code of Virginia and the Official Motor Vehicle Inspection Manual.

d. The business establishment must be financially stable. Its future existence should not be dependent upon appointment as an inspection station. The applicant and all persons to be associated with the inspection program must be in compliance with any judgment order or meeting all financial obligations, or both. The applicant and all persons to be associated with the inspection program must be in good financial standing for a period of at least one year.

Following any change in ownership, new ownership must show financial stability for a minimum of six months prior to their official inspection station appointment.

4. Each business must agree to provide the necessary space, equipment, and personnel to conduct inspections as required by the Department of State Police. Facilities and equipment will be maintained in a manner satisfactory to the superintendent. All safety inspectors will read and be thoroughly familiar with the instructions furnished for Official Inspection Stations and agree to abide by these instructions and to carefully inspect every motor vehicle, trailer, and semi-trailer presented for inspection as required by the Official Motor Vehicle Safety Inspection Manual. Businesses must operate inspection stations in strict accordance with the Code of Virginia and the Official Motor Vehicle Inspection Manual. The appointment of an inspection station may be canceled at any time by the superintendent and will be automatically canceled if any change in address, name, or ownership is made without proper notification.

5. Any applicant whose application is rejected or withdrawn may not reapply sooner than six months from the date he is notified of the rejection of his application or from the date the application is withdrawn.

6. Each business to be appointed will be assigned one of 11 classifications based upon the physical plant specifications or other criteria as follows:

a. Unlimited: The inspection lane shall be level or on the same plane and in good condition for 60 feet. The front portion of the lane shall be level or on the same plane for a minimum of 40 feet. The entrance shall be at least 13-1/2 feet in height and no less than nine feet in width. (Space should be adequate to allow a tractor truck towing a 53-foot trailer access to the inspection lane.)

b. Small exemption: The inspection lane shall be level or on the same plane for 40 feet. The entrance opening shall be at least 10 feet in height, eight feet in width, and adequate to accommodate vehicles 40 feet in length. Any vehicle exceeding 10 feet in height may be inspected if the building entrance will allow such vehicle to completely enter the designated inspection lane.

c. Large exemption: The inspection lane shall be level or on the same plane and in good condition for 60 feet. The front portion of the lane shall be level or on the same plane for a minimum of 40 feet. The entrance shall be at least 13-1/2 feet in height and no less than nine feet in width. (Space should be adequate to allow a tractor truck towing a 53-foot trailer access to the inspection lane.) This classification is required to inspect only vehicles with a GVWR exceeding 10,000 pounds.

d. Motorcycle: The inspection lane shall be level or on the same plane. The entrance shall be adequate to accommodate the motorcycle and the operator.

e. Unlimited trailer: The inspection lane shall be reasonably level and in good condition for 60 feet. The entrance shall be at least 13-1/2 feet in height and no less than nine feet in width. This classification is required to inspect all trailers.

f. Small trailer exemption: The inspection lane shall be reasonably level and in good condition for 40 feet. The entrance shall be at least 10 feet in height and adequate to accommodate trailers 40 feet in length. This classification is required to inspect only those trailers not exceeding 40 feet in length or 10 feet in height measured to the highest part of the trailer but not including racks, air conditioners, antennas, etc.

g. Large trailer exemption: The inspection lane shall be reasonably level and in good condition for 60 feet. The entrance shall be at least 13-1/2 feet in height and adequate to accommodate all legal size trailers. This classification is required to inspect only property-carrying trailers exceeding 10 feet in height or 40 feet in length.

h. Safety and emissions: The inspection lane shall be level or on the same plane. The lane must accommodate most passenger cars and light trucks. The emissions equipment must be placed in the lane at a location to allow the inspected vehicle to be positioned with all four wheels on the floor or on an above-ground ramp on a plane to the floor to accommodate headlight aiming and other required inspection procedures. Any above-ground structure must be constructed so as to permit proper steering, suspension, brake, and undercarriage inspection as outlined in the Official Motor Vehicle Safety Inspection Manual. A list of local inspection stations that can accommodate vehicles that cannot be safety inspected due to the pretenses of emissions equipment must be maintained and available for customers. A "bottle" jack or other appropriate lifting equipment may be used for safety inspection on above-ground structures.

i. Private station: The inspection lane shall be level or on the same plane. The entrance and size must be adequate to accommodate any vehicle in the fleet. An applicant who owns and operates less than 20 vehicles will not be considered.

j. Private station (fleet service contractor): The inspection lane shall be level or on the same plane. The entrance and size must be adequate to accommodate any vehicle in the fleet to be inspected. This classification will permit the inspection of all vehicles that the applicant has a written agreement to service and repair. An applicant who does not have at least six written agreements to service private fleets with at least five vehicles in each fleet or at least one written agreement to service a private fleet with at least 30 vehicles in the fleet will not be considered for this type of appointment. Vehicles not covered by a written agreement for service and repair, other than the vehicles owned by the applicant's company or corporation, shall not be inspected by a garage having this type of classification.

k. Private station (government): The inspection lane shall be level or on the same plane. The entrance and size must be adequate to accommodate any vehicle in the fleet to be inspected. This classification will permit the inspection of all vehicles in the government entity's fleet, the fleet of any volunteer or paid fire department, or any other unit or agency of the government structure having a written agreement with such governmental entity for repair, inspection service, or both. An applicant for this classification must own or have a written agreement to inspect 30 or more vehicles. Vehicles not owned by or covered by a written agreement shall not be inspected by a garage having this type of classification.

7. Classifications listed in subdivisions 6 a through 6 h of this subsection must be open to the public and have at least one safety inspector available to perform inspections during normal business hours as set forth in 19VAC30-70-10.

8. Private inspection station classifications may be assigned to businesses or governmental entities with fixed garage or repair facilities operating or contracting with vehicle fleets.

B. A representative of any official inspection station may apply to the Department of State Police in writing to request a change of the station's status.

1. An application form will be forwarded to the applicant.

2. The applicant will complete the application form and contact the Department of State Police in keeping with the application instructions. Applications will include all data as set forth in this section.

3. A Safety Division trooper will be assigned to complete the appropriate investigation to affect the change. A change in status investigation will include:

a. A review of the existing station file.

b. An update of the file to include personnel, facility, or other significant changes. Criteria for appointment and background investigation procedures for a change in status will be in keeping with this section.

c. Official inspection stations will be permitted to continue to perform safety inspections during a change of ownership investigation provided at least one safety inspector is retained from the prior owner.

d. If disqualifying criteria is revealed, the station's appointment shall be canceled until final disposition of the application is made or until issues of disqualifying criteria are resolved.

C. Once an official inspection station has been suspended, regardless of the cause for the suspension, management may request reinstatement up to 60 days prior to the expiration of the suspension period. Stations whose appointments are revoked may complete the application process as set forth for original appointments after the expiration of the period of revocation.

1. The applicant station must submit a letter to Safety Division Headquarters (Attention: Station Files) requesting reinstatement.

2. An application package will be forwarded to the applicant.

3. The completed application forms are to be returned to Safety Division Headquarters (Attention: Station Files).

4. After review, the application package is forwarded to the appropriate Safety Division Area Office for investigation.

a. The trooper assigned to the investigation will compare the information in the new application package to the information in the existing files.

b. The investigation will focus on any changes or inconsistencies.

c. The applicant station must meet all criteria for appointment as set forth in this section.

d. Any applicant whose application for reinstatement is rejected or withdrawn may not reapply sooner than six months from the date he is notified of the rejection or withdrawal of the application.

D. Failure to comply with the provisions of this section shall be grounds for termination of the application process or cancellation of the official inspection station's appointment. An applicant having an application terminated or an official inspection station having an appointment canceled for noncompliance may not reapply for a period of one year.

A. Upon request, the Inspector Certification Application (Form SP-170B) and Criminal History Record Request (Form SP-167) are provided online via the Virginia State Police website to individuals desiring appointment as certified safety inspectors.

1. The application package includes instructions to help guide the applicant through the process.

2. Applicants may be certified in any of the following classes after completing the necessary requirements and the appropriate examinations:

a. Class A: May inspect any motor vehicle, motorcycle, or trailer.

b. Class B: May inspect trailers only.

c. Class C: May inspect motorcycles only.

B. Applicants should immediately prepare for the written examination by studying the Official Motor Vehicle Safety Inspection Manual in its entirety.

1. When sufficiently prepared for the examination, the applicant should visit a testing site in his area to complete the appropriate examination.

2. The applicant must present his completed application in accordance with the provisions established in 19VAC30-70-9.2.

3. If the applicant's driver's license is expired, suspended, or revoked, the applicant will be advised, and the application destroyed. The applicant may reapply after his driver's license is reinstated.

C. The Class A inspector examination consists of five sections containing 20 questions each. A minimum score of 75% must be attained for each section. The Classes B and C inspector examinations will consist of 50 questions each. A minimum score of 74% must be attained. If the applicant fails the test, failure is noted at the end of Section I on the Form SP-170B with the word "failed" and the date. The application is returned to the applicant. Applicants failing to attain the minimum score are not allowed to test again for 30 days. Applicants failing a second or subsequent examination are not allowed to test again for six months.

D. The Inspectors Certification Application (Form SP-170B) and Criminal History Record Request (Form SP-167) for applicants who achieve a minimum score or greater is forwarded to Safety Division Headquarters.

1. The applicant's record is checked against safety inspector and Central Criminal Records Exchange (CCRE) files.

2. Inspection and criminal record information along with the applicant's driver transcript is forwarded with the application to the appropriate Safety Division Area Office for investigation.

3. A credit check is performed to determine that the applicant associated with the inspection program is in compliance with any judgment order or is meeting all financial obligations, or both.

E. A background investigation is conducted consisting of the following:

1. Verification that the applicant is at least 18 years of age.

2. Verification that the applicant has not less than one year's practical experience employed as an automotive technician repairing vehicles for the public, or six months of practical experience as an automotive mechanic combined with an additional and separate six months of mirroring a certified state inspector, or has satisfactorily completed a training program in the field of automotive mechanics approved by the Department of State Police. The following training programs in the field of automotive mechanics have been approved as a substitute for the one year's practical experience requirement:

a. The two-year associate degree or diploma programs in automotive technology offered by the Virginia Community College System consisting of the following minimum curriculum:

(1) Automotive Electrical Systems - three semester hours.

(2) Braking Systems - three semester hours.

(3) Emissions Control Systems - three semester hours.

(4) Suspension and Steering Systems - three semester hours.

(5) Vehicle Safety Inspection - two semester hours.

b. The 1,080-hour Career Technical Automotive Services Technology Program, offered by the Office of Career Technical Education, State Department of Education, in the various technical schools located throughout Virginia or be certified by the National Institute for Automotive Service Excellence (ASE), or both.

(1) Upon the successful completion of this course, including a practical test as defined in this section, the student must complete a Mechanics Certification Application (Form SP-170B) and a Criminal History Record Request (Form SP-167), pass a written test as defined in subsection C of this section, and submit to a background investigation as defined in this subsection. Upon successful completion of these requirements, the student, if 18 years of age, is certified as a safety inspector and issued a safety inspector license.

(2) If the student scores less than 75% on any part of the examination, the application will be returned to the certifying trooper. Students scoring less than 75% on any part of the examination may retest at the certifying trooper's next recertification testing date, but not sooner than 30 days from the date of the last examination. If the student passes the test at this time and is at least 18 years of age, he is issued a safety inspector license. Upon the student's 18th birthday, providing he still meets all of the requirements, the student will be issued a safety inspector license.

(3) Students failing the second written examination are not allowed to test again for six months. In order to retest the student must be at least 18 years of age and must complete the application process set forth for original certification.

c. The 1,500-hour Course #1 entitled "Auto-Diesel Technician Course" offered by the Nashville Auto Diesel College, Inc., 1524 Gallatin Road, Nashville, Tennessee 37206.

3. A determination of the applicant's mechanical ability through interviews with employers and customers.

4. A review of the applicant's current driving record on file with the Department of Motor Vehicles (DMV) is utilized in determining applicant's suitability for certification.

5. Determination of the character and reputation of the applicant through previous associates, employers, and records.

6. Determination of the applicant's attitude toward the inspection program and receptiveness to State Police supervision through personal interview.

7. The investigating trooper shall administer a practical examination to determine the applicant's ability to conduct a safety inspection. The applicant will conduct a complete inspection, including the use of the optical headlight aimer. This shall be conducted at the applicant's station of employment. If the applicant is not employed at a certified inspection station, the applicant may make arrangement with one to conduct practical testing.

F. Any applicant whose application is withdrawn or rejected due to incomplete documentation may not reapply sooner than six months from the date of the withdrawal or the date the applicant are notified of the rejection of his application. Any applicant whose application is denied may not reapply sooner than 12 months from the date of the letter notifying the denial.

G. When a safety inspector is certified, the bottom of the Form SP-170B is completed by the certifying trooper. The classification for which the safety inspector is being certified and the date of certification must be entered by the trooper on the bottom of the Form SP-170B. The Form SP-170B shall then be forwarded to the Safety Division Area Office.

H. Upon certification, the supervising trooper fills out the temporary inspector's license in triplicate, forwarding the original (white copy) to Safety Division Headquarters, issuing the canary copy to the inspector, and retaining the pink copy at the Safety Division Area Office for six months. Once the safety inspector has been issued a temporary license, he is eligible to begin inspecting.

I. All safety inspector licenses shall be valid for a period of three years.

19VAC30-70-9.2

19VAC30-70-9.2. Examinations for inspector's license.

A. The Department of State Police administers the written examination for original certification for all inspectors. With few exceptions, recertifications are done at the normal testing sites along with original certification tests.

B. In order for an individual to become a certified safety inspector, the following actions shall be followed:

1. The person shall download the following forms from the Virginia State Police website:

a. Inspector Certification Application, Form SP-170B;

b. Criminal History Record Request, Form SP-167; and

c. Inspector Application Worksheet.

2. The applicant shall (i) complete Form SP-170B in its entirety and have it notarized; (ii) complete and have notarized Form SP-167 with appropriate credit card information or an attached $15 cashier's check, business check or money order payable to "Virginia State Police"; and (iii) complete the Inspector Applicant Worksheet with two character references, two mechanical references, places of employment, and qualified automotive training, or schools completed or mechanical experience.

3. The applicant shall then take the completed application forms to any State Police testing site and present it to the trooper conducting the written examination. Applicants arriving after the designated testing time are not eligible to participate in the written examination.

4. The trooper verifies the notarizations and checks the driver's license for validity and identification of the applicant. If the applicant's driver's license is found to be expired, suspended, or revoked, the applicant is advised, and the application is destroyed. The applicant may reapply once the driver's license has been reissued or reinstated.

5. If the applicant successfully passes the test, the trooper notes at the end of Section I on the Form SP-170B the word "passed" and the date. The trooper signs the test and sends it to Safety Division Headquarters, Inspectors File Section for further processing and investigation.

6. The Class A examination consists of five sections: general information, brakes, suspension, lights, and glass. Each section contains 20 questions. A minimum score of 75% must be attained for each section and for the practical examination. The Classes B and C examinations consist of 50 questions each. A minimum score of 74 must be attained on the written and practical examination.

7. If the applicant fails the test, failure is noted at the end of Section I on the Form SP-170B with the word "failed" and the date.

8. If the applicant desires to test again for the written or practical test, he may do so after 30 days. If the applicant is again unsuccessful in passing either examination, the trooper shall take the application forms and forward them to Safety Division Headquarters, Inspector Files Section. The applicant may contact his assigned Safety Division trooper or the local Safety Division Area Office after six months to reapply.

C. Recertification.

1. Safety inspectors desiring to renew their inspector's license must participate in the recertification written examination. Inspectors arriving after the designated testing time are not eligible to participate in the written examination.

2. All safety inspectors are required to satisfactorily pass the appropriate examination for the license the inspector holds.

3. A safety inspector is not permitted to perform inspections after the expiration date of his inspector's license.

4. A safety inspector's license shall be valid for a period of three years.

5. All safety inspectors' licenses display an inspector's VSP number and do not display the social security number. The inspector's VSP number is written on the inspection sticker receipt or displayed on the automated MVIP receipt.

6. Safety inspector testing sites are not included on an inspection bulletin. Testing site information is updated in the computer system so that the usual letters going to inspectors to remind them of their upcoming recertification contain the updated information. All Safety Division Area Offices also have the updated information.

7. If the safety inspector has any questions about the testing sites, the safety inspector should contact the Safety Division Area Office closest to him. The office numbers are:

 

Area 61 (Richmond)

804‑743‑2217

 

Area 62 (Culpeper)

540‑829‑7414

 

Area 63 (Amherst)

434‑946‑7676

 

Area 64 (Wytheville)

276‑228‑6220

 

Area 65 (Suffolk)

757‑925‑2432

 

Area 66 (Salem)

540‑387‑5437

 

Area 67 (Fairfax)

703‑803‑2622

D. Vo-tech students who successfully complete the Vocational Automotive Mechanics Course and who are expected to graduate from the program with the required 1,080 hours and meet the requirements of the Department of State Police are certified as safety inspectors.

1. The vo-tech instructor contacts his assigned Safety Division trooper or the local Safety Division Area Office by March 15 of each year. The written examination is scheduled for students who are at least 18 years of age or who will be at least 18 years of age by March 31 of that year.

2. The Safety Division troopers responsible for administering the written examinations at the vo-tech centers forward sufficient applications, Form SP-170B, for each student to complete prior to the testing date. A Criminal History Record Request (Form SP-167) if the student is at least 18 years of age must also be completed. The Safety Division trooper indicates at the top of the Form SP-170B the name of the vo-tech school where the examination is given.

3. The trooper verifies the notarizations and checks the driver's license for validity and identification of the applicant. If the applicant's driver's license is found to be expired, suspended, or revoked, the applicant is advised, and the application is destroyed. The applicant may reapply once the driver's license has been reissued or reinstated.

4. If the applicant successfully completes the written examination, the trooper notes at the end of Section I on the Form SP-170B the word "passed" and the date. The trooper signs the test and forwards it to Safety Division Headquarters, Mechanics File Section for further processing and investigation. Due to the age of these students, this should be done in a minimal amount of time.

5. If the applicant fails the test, failure is noted at the end of Section I on the Form SP-170B with the word "failed" and the date.

a. The Safety Division trooper only administers one written examination at the vo-tech center. Those students who fail the first written examination may retest, but not sooner than 30 days from the date of the last written examination. Those students who fail the first written examination keep the Form SP-170B in their possessions and present it to the Safety Division trooper at the test site prior to taking the second written examination.

b. The second written examination is not administered to the students prior to the end of the school year. Prior to taking the second written examination, the student shall have completed the Vocational Automotive Mechanics Course and must be employed at an official inspection station. These students are not required to have completed the one year of practical experience as an automotive mechanic.

c. For those students who pass the second written examination, the Safety Division trooper will forward the student's Form SP-170B to the Safety Division for further processing and investigation. Those students who successfully pass all phases for original certification are then issued a temporary inspector license by the Safety Division trooper.

d. Students failing the second written examination are not allowed to test again for six months and must complete the application process as set forth for original certification.

6. The written examination consists of five sections: general information, brakes, suspension, lights, and glass. Each section contains 20 questions. A minimum score of 75% must be attained for each section.

7. Those students who successfully complete all phases of the written examination and background checks are then administered a practical examination. The vo-tech instructor, who holds a valid Class A Safety Inspector's License, administers the practical "Class A" examination to each student who is expected to graduate from the program. The Safety Division trooper should be on hand to observe at least some of the practical examinations administered by the vo-tech instructor to ensure that testing is administered according to Safety Division regulations.

8. Those students who successfully complete all phases for original certification by March 31 will be issued a temporary inspector license by the Safety Division trooper. The Safety Division trooper then forwards the completed temporary inspector license to the Safety Division Headquarters, Inspector Files Section.

a. The Safety Division mails a permanent inspector's license to the student, provided he is at least 18 years of age by March 31 of that year.

b. The vo-tech instructor is required to contact the Safety Division trooper prior to the end of the school year if any student fails to complete the Vocational Automotive Mechanics Course.

c. Any student who fails to complete the Vocational Automotive Mechanics Course is not licensed as a certified safety inspector and is required to complete the application process as set forth for original certification.

9. Those students who will be at least 18 years of age after March 31 of that year and have successfully completed the Vocational Automotive Mechanics Course must contact the Safety Division trooper assigned to the inspection stations where they are employed and complete the application process as set forth for original certification. These students are not required to have completed the one year of practical experience as an automotive mechanic.

19VAC30-70-9.3

19VAC30-70-9.3. Reinstatement of safety inspector license; classification change; recertification.

A. Reinstatement of safety inspector licenses following a period of suspension or revocation.

1. The inspector shall contact his supervising trooper or nearest Safety Division Area Office to initiate the reinstatement process.

2. If the inspector is suspended for less than six months, the safety inspector's license will be held at the local Safety Division Area Office and returned upon the expiration of the suspension period. A check will be made by the supervising trooper with Department of Motor Vehicles (DMV) prior to reinstatement.

3. Once a safety inspector's license has been suspended for a period of six months or more, regardless of the cause for suspension, no application Form SP-170B is required for reinstatement; however, Form SP-170D and Form SP-167 must be completed. The supervising trooper checks with DMV, all court jurisdictions, and the Central Criminal Records Exchange. The supervising trooper shall also review a credit report prior to reinstatement of the inspector.

4. If the suspended inspector's license expires during the suspension period, the inspector may complete the process for inspector recertification as set forth in this section. The trooper administering the test will retain all documentation. The inspector's license will be returned at the end of the suspension period, if the suspended inspector's records indicate he is suitable for reinstatement, and the appropriate documents forwarded to the Safety Division.

5. Inspectors whose safety inspector's licenses have been revoked must complete the application process for initial certification as set forth in this section.

B. Safety inspectors who desire to change their license classification must complete the written and practical examinations as outlined in 19VAC30-70-9.2.

C. Safety inspectors desiring to renew their inspector's license must participate in the recertification process. The process requires the following:

1. Review of training materials as may be presented at the certification testing site by State Police personnel.

2. Completion of the appropriate examination for the class license the inspector holds. A minimum score must be attained as previously outlined in 19VAC30-70-9.2.

3. An inspector holding an expired license may be tested as long as his license has not been expired more than one month. During the period of expiration, he will not be permitted to perform inspections.

An inspector holding an expired inspector license that has not been expired more than one month and who fails the recertification examination the first time during this one-month grace period may be retested one additional time not sooner than 30 days from the date of the last recertification examination. Inspectors failing this subsequent examination are not retested for six months and must complete the application process as set forth for initial certification.

D. When a request for reinstatement is denied, inspectors who are suspended for a period of six months or more may not reapply sooner than 12 months from the date of the letter notifying the denial. Following an initial certification investigation for a revoked inspector, if the revoked inspector is denied, he may not reapply sooner than 12 months from the date of the letter notifying the denial.

19VAC30-70-10

Part II
Inspection Requirements

19VAC30-70-10. Official inspection station requirements.

A. Official inspection stations, except private appointments, shall be open at least eight hours of each normal business day and shall be able to perform inspections 12 months throughout the year, except during illness of limited duration or normal vacation.

1. Normal business hours, Monday through Friday, are defined as an eight-hour period of time between 8 a.m. and 6 p.m.

2. Stations are not prohibited from performing inspections at times other than during normal business hours.

3. A station that advertises inspections beyond normal business hours shall be able to perform such inspections.

4. If a station desires to maintain business hours that are different from those defined in this section, written permission must be obtained from the safety officer and a sign setting forth the inspection hours must be posted conspicuously at the station where it can be observed by a person desiring to have a vehicle inspected.

5. Stations seeking to participate on a part-time basis, due to not having a full-time inspector available during normal business hours, shall be available for inspections for a minimum of 20 hours per week and shall notify their supervising trooper of the following items to have documented in their files:

a. Hours of operation the station will be conducting safety inspections.

b. Intended methods of notifying the public what hours inspections are available.

c. Name of the inspector who will be designated for part-time hours of operation.

d. Time period established for ownership to find and employ a full-time inspector.

B. At least one full-time safety inspector (stations in compliance with subdivision A 5 of this section excluded), to perform inspections and one inspection lane meeting the minimum requirements shall be available for inspection at all times during the normal business day. All inspections must be made only at the locations and in the inspection lane approved by the Department of State Police. All stations shall have other lanes, bays, or areas in which repairs can be made so the inspection lane can remain available.

The designated inspection areas, including any location where customers are permitted to enter when submitting vehicles for inspection, must be kept clean and free from excessive dirt, grease, and loose materials. If requested, customers presenting vehicles for inspection shall be allowed to observe the inspection process from a safe location designated by the station.

C. Inspection station facilities must be properly maintained and must present a businesslike appearance to the general public. Property adjacent to the inspection station that is owned or controlled by the station must be free of debris, litter, used parts and junk vehicles. Vehicles properly contained within fenced storage areas shall be deemed to comply with this requirement.

D. Official inspection stations may, at their discretion, accept vehicles on a first-come, first served first-served basis or by prescheduled appointments for the safety inspection of a motor vehicle pursuant to § 46.2-1157 of the Code of Virginia. Appointments shall be made for those motorists that are required by subdivision A 12 of § 46.2-1158.01 of the Code of Virginia. Stations that take in vehicles for inspection at the beginning of the work day shall not be required to stop inspecting those vehicles to provide an inspection for a drive-in request, provided inspections are currently being performed at the time and will continue throughout the day.

Stations shall make every effort to keep the designated inspection lanes available. Stations with more than one repair bay shall not perform work in the designated inspection lanes when customers are waiting for an inspection. This will not apply to minor adjustments that require minimal time to perform. Stations shall not let vehicles occupy the designated inspection lanes while awaiting parts or customer authorization to complete the inspection pursuant to 19VAC30-70-60.

E. Safety inspectors, managers who supervise inspection activities, and business owners, through participation in the Official Motor Vehicle Inspection Program, are representatives of the Department of State Police and should conduct themselves in a manner to avoid controversy in dealing with customers presenting vehicles for inspection. The use of profanity or verbal abuse directed at customers presenting their vehicles for inspection will be grounds for suspension from participation in the inspection program and will be considered a Class IV offense as set forth in 19VAC30-70-6. Controversy that cannot be calmly resolved by the safety inspector, managers, and owners should be referred to the supervising trooper for handling.

F. The "Certificate of Appointment" must be framed under glass or clear plastic and posted in the customer waiting area where it can be observed and read by a person submitting a vehicle for inspection.

Inspection stations must have garage liability insurance in the amount of at least $500,000 with an approved surplus lines carrier or insurance company licensed to write such insurance in this Commonwealth. This requirement shall not apply to inspection stations that only inspect their company-owned, government-owned, or leased vehicles.

G. The required "Official Inspection Procedure" sheet and the "Direct Inquiries" sheet furnished to each station must both be framed under glass or clear plastic and posted conspicuously in the customer waiting area where they can be observed and read by a person submitting a vehicle for inspection.

H. The poster designating the station as an official inspection station shall be posted in a prominent location, outside or visible outside the station, to alert passersby that inspection services are available. Private inspection stations shall not display an outside poster.

I. Each official inspection station shall display a list with the names and license expiration dates of each active inspector associated to the station within the MVIP Motor Vehicle Inspection Program (MVIP) system, adjacent to the certificate of appointment. All inspectors listed must be actively employed by the station. The Official Motor Vehicle Safety Inspection Manual will be kept at or near the point of inspection for ready reference. The manual may be kept in written or electronic form.

J. Important -- Any change in name, ownership or location of any official inspection station cancels the appointment of that station, and the Department of State Police must be notified immediately. The department shall be notified when an official inspection station discontinues operation.

K. All inspection supplies, inspection binders and manual, unused stickers, duplicates of certificates issued, bulletins and other forms are the property of the Department of State Police and must be safeguarded against loss.

L. Inspection supplies issued to an inspection station can be used only by that station and are not to be loaned or reissued to any other station.

1. Stations must maintain a sufficient supply of approval stickers, trailer and motorcycle approval stickers, rejection stickers and inserts. When reordering supplies, station owners or managers shall request sufficient supplies to sustain their business for at least six months. However, it is realized that a few some stations will not be able to comply with the six-month requirement since there is a maximum of 100 books per order limit. Also, when ordering supplies, the following information should be considered so that the station does not order an excessive amount of supplies: each book of approval stickers contains 25 stickers, the rejection book contains 50 stickers, the month inserts are packaged in strips of 50 each, and trailer and motorcycle decals are five per strip. In December of each year, a supply of year inserts will be shipped to each station based on the station's previous year's usage. In November, each station shall check its stock of month inserts and order what is needed for the months of January through June. In May, the same should be done for the months of July through December.

Stations receive biannual (November/May) supply shipments each year. The first supply shipment (November) includes car/truck approval stickers, car/truck month inserts, and trailer/motorcycle year inserts. The second supply shipment (May) contains car/truck approval stickers and car/truck month inserts. Supply amounts for each shipment are calculated upon the stations current and previous year inspection trends.

Stations are responsible for maintaining an adequate supply of inspections supplies to operate efficiently and without delay; therefore, after stations receive the biannual shipment, additional supplies can be ordered through the MVIP station account.

2. Inspection stations that exhaust any type of their supplies, such as approval stickers, trailer and motorcycle approval stickers, rejection stickers, or inserts shall immediately stop all inspection operations and contact their supervising trooper or the nearest Safety Division Area Office.

M. All losses of stickers must be reported immediately to the supervising inspection trooper or the nearest Safety Division Area Office.

N. Every precaution against the loss of stickers must be taken. If the loss occurs through carelessness or neglect, a suspension of the station may result.

O. Manuals The Official Motor Vehicle Safety Inspection Manual must be kept at or near the point of inspection for ready reference. Additional manuals, bulletins, other regulations, and lists of approved equipment must also be available at all times for reference and. All reference materials may be kept in written or electronic form. Revisions to the Motor Vehicle Safety Inspection Manual will be sent to each station electronically through the MVIP system. Station management shall be responsible to see that each safety inspector is familiar with all bulletins and manual revisions and shall be required to furnish evidence to the department that all bulletins and manual revisions have been reviewed by each licensed inspector.

A copy of the diagram drawn by the investigating trooper, showing the approved inspection lane or lanes, will be maintained for review and kept available with the station's inspection supplies.

P. Private appointment may be made of company stations or government stations that own and operate a minimum of 20 vehicles and they may inspect only company-owned or government-owned vehicles respectively. When authorized by the department, they may inspect vehicles of a wholly-owned subsidiary or leased vehicles.

1. A private station may perform inspections during each month of the year or may elect to inspect only during certain designated months.

2. A private station not electing to inspect vehicles every month of the year that finds it necessary to inspect a vehicle during a month other than those selected for inspection may issue a sticker to the vehicle from the nearest past inspection month.

Q. All official inspection station owners, managers, and certified safety inspectors shall comply with the Virginia inspection laws and the inspection rules and regulations and will adhere to all instructions given by the supervising trooper or the Safety Division. Reports of violations will be investigated and, if found to be valid, may result in the suspension of the station, suspension of the inspector, possible court action, or other appropriate action, or any combination of these actions. Repeated violations or serious violations may result in a revocation of the inspector or station appointment, or both, by the superintendent.

R. The arrest of any person associated with the inspection program for a criminal offense of a nature that would tend to immediately reflect upon the integrity and reputation of the Department of State Police may be grounds for an immediate suspension and the conviction for such an offense inactive station status until final court disposition. Any finding other than acquittal may result in a suspension or revocation of the station's appointment.

S. When a station has been suspended or revoked, it must release to an employee of the Department of State Police all inspection supplies, posters, and papers including the certificate of appointment. Failure to do so is a violation of § 46.2-1172 of the Code of Virginia.

T. The authority of the superintendent to suspend the designation or appointment of an official inspection station as provided in § 46.2-1163 of the Code of Virginia, or to suspend the certification of an inspector designated to perform inspections at an official inspection station, and, in keeping with the provisions of § 46.2-1166 of the Code of Virginia, is hereby delegated to any of the following supervisory ranks of the Department of State Police: Lieutenant Colonel, Major, Captain, Lieutenant, First Sergeant and Sergeant.

U. Each station must purchase and keep in proper operating condition the following equipment: computer, printer, internet connection, paper hole punch, black ball point pen or pens or black marker or markers, sticker scraper with replacement razor blades, tire tread depth gauge, amp meter, headlight and auxiliary lamp adjustment tools, 12-inch ruler, 25-foot measuring tape, torque wrench or torque sticks, brake pads/shoes/disc/drum measuring device, dial indicator, micrometer, pry bars, roller jack (at least 4-ton), and an approved type optical headlight aiming device. Each station that requests an additional inspection lane that is not in close proximity to the originally approved inspection lane must purchase an additional approved headlight machine for each lane that meets the minimum requirements. Stations are required to have one of the following headlight aiming devices: Hopkins Vision1, Hopkins Vision 100, American Aimers Vision 100, American Aimers Vision 2 Pro, or the Symtech (former L.E.T.), DVA-6, HBA-5, PLA-11, and PLA-12. This shall not apply to "trailer-only" inspection stations.

19VAC30-70-10.1

19VAC30-70-10.1. Official inspection station appointment.

A. These procedures are applicable to the application process for initial appointment, reclassification of appointment, change in ownership, change in name, and reinstatement of the appointment for an official inspection station following a period of suspension or revocation.

For investigations involving changes to the original report, only those areas of inquiry that have changed need to be reported.

For changes in station name, location, and classification only, a narrative report is not required. These requests may be reported on the Form SP-164. This report should include information pertinent to the change. A statement should be included to report verification of information contained in the station's new application for appointment.

1. Any garage or other facility that routinely performs motor vehicle, motorcycle, or trailer repairs may apply to the Department of State Police in writing for appointment as an Official Safety Inspection Station.

a. The Department of State Police will forward an application package to the applicant.

b. The application forms are to be completed and returned to the supervising trooper processing the application within 45 days.

c. The application shall include the names, addresses, email addresses, telephone numbers, dates of birth, and social security numbers for the applicant and each person who will supervise or otherwise participate in the program. Each person is also required to execute an Authorization for Release of Information Form (SP-170-D) and a Criminal History Record Request (Form SP-167). When a corporation with other established inspection stations is applying for an additional location, it shall not be necessary for the corporate officers to complete the Form SP-167 or undergo the usual background investigation. In these situations, the Department of State Police is only concerned with the personnel who will be responsible for handling and securing the safety inspection supplies.

2. Each inspection station application is reviewed, and the applicant must meet the following criteria:

a. The facility must have been in business at its present location for a minimum of 90 days.

(1) This requirement does not apply to a change in location for a previously appointed station.

(2) This requirement does not apply to a repair garage that is an established business and is expanding its mechanical convenience to the general public by the addition of other repair locations.

(3) This requirement does not apply to a business license as a franchised dealer of new vehicles.

b. The facility must perform motor vehicle, motorcycle, or trailer repairs routinely.

c. The station must have on hand or be willing to purchase the necessary equipment as identified by the Department of State Police for performing safety inspections.

d. The station must employ or be willing to employ at least one safety inspector with the appropriate license for the desired station's classification.

e. The facility's physical plant must meet the specific standards for the station classification for which the appointment is required.

3. Each applicant station must undergo a background investigation to determine if the business and associated personnel meet the following minimum criteria:

a. A review of the history of management and all persons employed who will participate in the inspection program must reflect general compliance with all federal, state, and local laws.

b. The character, attitude, knowledge of safety inspection requirements, mechanical ability, and experience of each individual who will perform or supervise safety inspections must be satisfactory.

c. The applicant and all participants must be familiar with and agree to comply with the Official Motor Vehicle Inspection Manual. Each vehicle presented for safety inspection must be inspected in strict compliance with the Code of Virginia and the Official Motor Vehicle Inspection Manual.

d. The business establishment must be financially stable. Its future existence should not be dependent upon appointment as an inspection station. The applicant and all persons to be associated with the inspection program must be in compliance with any judgment order or meeting all financial obligations, or both. The applicant and all persons to be associated with the inspection program must be in good financial standing for a period of at least one year.

Following any change in ownership, new ownership must show financial stability for a minimum of 90 days prior to their official inspection station appointment.

4. Each business must agree to provide the necessary space, equipment, and personnel to conduct inspections as required by the Department of State Police. Facilities and equipment must be maintained in a manner satisfactory to the superintendent. All safety inspectors must read and be thoroughly familiar with the instructions furnished for Official Inspection Stations and agree to abide by these instructions and to carefully inspect every motor vehicle, trailer, and semi-trailer presented for inspection as required by the Official Motor Vehicle Safety Inspection Manual. Businesses must operate inspection stations in strict accordance with the Code of Virginia and the Official Motor Vehicle Inspection Manual. The appointment of an inspection station may be canceled at any time by the superintendent and are automatically canceled if any change in address, name, or ownership is made without proper notification.

5. Any applicant whose application is withdrawn, or rejected due to incomplete documentation, may not reapply sooner than six months from the date of the withdrawal or the date the applicant is notified of the rejection of his application. Any applicant whose application is denied may not reapply sooner than 12 months from the date of the letter notifying the denial.

6. Each business to be appointed will be assigned one of 11 classifications based upon the physical plant specifications or other criteria as follows:

a. Unlimited: The inspection lane shall be level or on the same plane and in good condition for 60 feet. The front portion of the lane shall be level or on the same plane for a minimum of 40 feet. The entrance shall be at least 13-1/2 feet in height and no less than nine feet in width. Space should be adequate to allow a tractor truck towing a 53-foot trailer access to the inspection lane.

b. Small exemption: The inspection lane shall be level or on the same plane for 40 feet. The entrance opening shall be at least 10 feet in height, eight feet in width, and adequate to accommodate vehicles 40 feet in length. Any vehicle exceeding 10 feet in height may be inspected if the building entrance will allow such vehicle to completely enter the designated inspection lane.

c. Large exemption: The inspection lane shall be level or on the same plane and in good condition for 60 feet. The front portion of the lane shall be level or on the same plane for a minimum of 40 feet. The entrance shall be at least 13-1/2 feet in height and no less than nine feet in width. Space should be adequate to allow a tractor truck towing a 53-foot trailer access to the inspection lane. This classification is required to inspect only vehicles with a gross vehicle weight rating (GVWR) exceeding 10,000 pounds.

d. Motorcycle: The inspection lane shall be level or on the same plane. The entrance shall be adequate to accommodate the motorcycle and the operator.

e. Unlimited trailer: The inspection lane shall be reasonably level and in good condition for 60 feet. The entrance shall be at least 13-1/2 feet in height and no less than nine feet in width. This classification is required to inspect all trailers.

f. Small trailer exemption: The inspection lane shall be reasonably level and in good condition for 40 feet. The entrance shall be at least 10 feet in height and adequate to accommodate trailers 40 feet in length. This classification is required to inspect only those trailers not exceeding 40 feet in length or 10 feet in height measured to the highest part of the trailer but not including racks, air conditioners, antennas, etc.

g. Large trailer exemption: The inspection lane shall be reasonably level and in good condition for 60 feet. The entrance shall be at least 13-1/2 feet in height and adequate to accommodate all legal size trailers. This classification is required to inspect only property-carrying trailers exceeding 10 feet in height or 40 feet in length.

h. Safety and emissions: The inspection lane shall be level or on the same plane. The lane must accommodate most passenger cars and light trucks. The emissions equipment must be placed in the lane at a location to allow the inspected vehicle to be positioned with all four wheels on the floor or on an above-ground ramp on a plane to the floor to accommodate headlight aiming and other required inspection procedures. Any above-ground structure must be constructed so as to permit proper steering, suspension, brake, and undercarriage inspection as outlined in the Official Motor Vehicle Safety Inspection Manual. A list of local inspection stations that can accommodate vehicles that cannot be safety inspected due to the pretenses of emissions equipment must be maintained and available for customers. A "bottle" jack or other appropriate lifting equipment may be used for safety inspection on above-ground structures.

i. Private station: The inspection lane shall be level or on the same plane. The entrance and size must be adequate to accommodate any vehicle in the fleet. An applicant who owns and operates fewer than 20 vehicles will not be considered.

j. Private station (fleet service contractor): The inspection lane shall be level or on the same plane. The entrance and size must be adequate to accommodate any vehicle in the fleet to be inspected. This classification will permit the inspection of all vehicles that the applicant has a written agreement to service and repair. An applicant who does not have at least six written agreements to service private fleets with at least five vehicles in each fleet or at least one written agreement to service a private fleet with at least 30 vehicles in the fleet will not be considered for this type of appointment. Vehicles not covered by a written agreement for service and repair, other than the vehicles owned by the applicant's company or corporation, shall not be inspected by a garage having this type of classification.

k. Private station (government): The inspection lane shall be level or on the same plane. The entrance and size must be adequate to accommodate any vehicle in the fleet to be inspected. This classification permits the inspection of all vehicles in the government entity's fleet, the fleet of any volunteer or paid fire department, or any other unit or agency of the government structure having a written agreement with such governmental entity for repair, inspection service, or both. An applicant for this classification must own or have a written agreement to inspect 30 or more vehicles. Vehicles not owned by or covered by a written agreement shall not be inspected by a garage having this type of classification.

7. Classifications listed in subdivisions 6 a through 6 h of this subsection must be open to the public and have at least one safety inspector available to perform inspections during normal business hours as set forth in 19VAC30-70-10.

8. Private inspection station classifications may be assigned to businesses or governmental entities with fixed garage or repair facilities operating or contracting with vehicle fleets.

B. A representative of any official inspection station may apply to the Department of State Police in writing to request a change of the station's status.

1. An application form is forwarded to the applicant.

2. The applicant completes the application form and contacts the Department of State Police in keeping with the application instructions. Applications must include all data as set forth in this section.

3. A Safety Division trooper is assigned to complete the appropriate investigation to affect the change. A change in status investigation includes the following:

a. A review of the existing station file.

b. An update of the file to include personnel, facility, or other significant changes. Criteria for appointment and background investigation procedures for a change in status will be in keeping with this section.

c. Official inspection stations are permitted to continue to perform safety inspections during a change of ownership investigation provided at least one safety inspector is retained from the prior owner.

d. If disqualifying criteria is revealed, the station's appointment shall be canceled until final disposition of the application is made or until issues of disqualifying criteria are resolved.

C. Once an official inspection station has been suspended, regardless of the cause for the suspension, management may request reinstatement up to 60 days prior to the expiration of the suspension period. Stations whose appointments are revoked may complete the application process as set forth for original appointments after the expiration of the period of revocation.

1. The applicant station must submit a letter to Safety Division Headquarters (Attention: Station Files) requesting reinstatement.

2. An application package is forwarded to the applicant.

3. The completed application forms must be returned to Safety Division Headquarters (Attention: Station Files).

4. After review, the application package is forwarded to the appropriate Safety Division Area Office for investigation.

a. The trooper assigned to the investigation compares the information in the new application package to the information in the existing files.

b. The investigation focuses on any changes or inconsistencies.

c. The applicant station must meet all criteria for appointment as set forth in this section.

d. Any applicant whose application for reinstatement is rejected or withdrawn may not reapply sooner than six months from the date he is notified of the rejection or withdrawal of the application.

D. When a request for reinstatement is denied, a station suspended a period of six months or more may not reapply sooner than 12 months from the date of the letter notifying the denial. Following an original appointment investigation for a revoked station, if the revoked station is denied, it may not reapply sooner than 12 months from the date of the letter notifying the denial.

19VAC30-70-20

19VAC30-70-20. General inspection requirements.

A. Each official inspection station must inspect every vehicle presented for inspection as prescribed by this chapter, either approving or rejecting it. Inspections will not be performed unless requested.

1. Dealers' vehicles shall be inspected according to these standards. The dealer's name rather than the license number shall be shown on the rear of the approval or rejection sticker.

2. Out-of-state vehicles may be inspected, but shall not be approved unless they meet the requirements of the Official Motor Vehicle Safety Inspection Manual.

3. When a vehicle is presented for inspection, the previous approval sticker, if any, on the vehicle shall be removed and destroyed before any inspection is conducted (except a rejection sticker). For purposes of the safety inspection program, "destroyed" shall mean that the previous inspection sticker will be disposed of in a manner so it cannot be reused or placed on another vehicle's windshield. After removing the inspection sticker, the safety inspector who is to perform the inspection must drive the vehicle into an approved inspection lane unless the safety inspector is not qualified to operate the vehicle. During the operation of the vehicle, the safety inspector must make application of the service and parking brakes and check for conditions as set forth in the Service Brake Section of the Official Motor Vehicle Safety Inspection Manual applicable to the vehicle being inspected.

WARNING: No razor blades or similar devices should be used to remove stickers from "Securiflex," "Anti-Lacerative" or "Inner Shield" type windshield. These windshields are identified as AS-14. Any questions concerning removal should be directed to the nearest Safety Division Area Office.

B. Each inspection shall be a complete, uninterrupted inspection and shall include a check of all applicable items in the Official Motor Vehicle Safety Inspection Manual. All repair tools and testing equipment required prior to a station's appointment shall be properly maintained and available for use during each inspection.

C. The term "inspection" as used in this chapter shall not include repairs or adjustments. Repairs or adjustments necessary to bring the vehicle in conformity with this chapter may be made by agreement between the owner and such station or whatever repair shop the owner may select. When requested to do so by the person submitting a vehicle for inspection, any repairs or adjustments necessary to bring the vehicle into compliance with the inspection program rules and regulations shall be made by the inspection station performing the inspection. The inspection station management may utilize the option of subcontracting the repairs or adjustments provided the application filed for the station appointment reflected that such repairs or adjustments will be subcontracted.

D. Each vehicle that meets the requirements as set forth in this chapter shall be issued an approval sticker. Those vehicles that do not meet the inspection requirements shall be issued a rejection sticker. Any trailer required to be inspected under the provisions of the Code of Virginia may, only if the size or configuration of the trailer and the size and configuration of the facilities of the inspection station prevent the trailer from being inspected inside the inspection station, be inspected outside the inspection station. The location on the outside of an inspection station where trailers may be inspected shall be approved by the Department of State Police and shown on the station diagram.

E. Inspections may be made when it is raining or snowing. Care must be exercised when making inspections in inclement weather. Vehicles covered with ice, snow, mud or other debris to the extent that required parts cannot be inspected, may be refused inspection until the operator removes such debris.

F. A certified safety inspector shall be prohibited from conducting safety inspection examinations on any vehicle registered to himself. This restriction shall also apply to vehicles registered outside of the Commonwealth of Virginia.

19VAC30-70-25

19VAC30-70-25. Exceptions to motor vehicle inspection requirements.

A. The following shall be exempt from inspection as required by § 46.2-1157 of the Code of Virginia:

1. Four-wheel vehicles weighing less than 500 pounds and having less than six horsepower;

2. Boat, utility, or travel trailers that are not equipped with brakes;

3. Antique motor vehicles or antique trailers as defined in § 46.2-100 of the Code of Virginia and licensed pursuant to § 46.2-730 of the Code of Virginia;

4. Any motor vehicle, trailer, or semitrailer that is outside the Commonwealth at the time its inspection expires when operated by the most direct route to the owner's or operator's place of residence or the owner's legal place of business in the Commonwealth;

5. A truck, tractor truck, trailer, or semitrailer for which the period fixed for inspection has expired while the vehicle was outside the Commonwealth (i) from a point outside the Commonwealth to the place where such vehicle is kept or garaged within the Commonwealth or (ii) to a destination within the Commonwealth where such vehicle will be (a) unloaded within 24 hours of entering the Commonwealth, (b) inspected within such 24-hour period, and (c) operated, after being unloaded, only to an inspection station or to the place where it is kept or garaged within the Commonwealth;

6. New motor vehicles, new trailers, or new semitrailers may be operated upon the highways of Virginia for the purpose of delivery from the place of manufacture to the dealer's or distributor's designated place of business or between places of business if such manufacturer, dealer, or distributor has more than one place of business, without being inspected; dealers or distributors may take delivery and operate upon the highways of Virginia new motor vehicles, new trailers, or new semitrailers from another dealer or distributor provided a motor vehicle, trailer, or semitrailer shall not be considered new if driven upon the highways for any purpose other than the delivery of the vehicle;

7. New motor vehicles, new trailers, or new semitrailers bearing a manufacturer's license may be operated for test purposes by the manufacturer without an inspection;

8. Motor vehicles, trailers, or semitrailers may be operated for test purposes by a certified inspector without an inspection sticker during the performance of an official inspection;

9. New motor vehicles, new trailers, or new semitrailers may be operated upon the highways of Virginia over the most direct route to a location for installation of a permanent body without being inspected;

10. Motor vehicles, trailers, or semitrailers purchased outside the Commonwealth may be driven to the purchaser's place of residence or the dealer's or distributor's designated place of business without being inspected;

11. Prior to purchase from auto auctions within the Commonwealth, motor vehicles, trailers, or semitrailers may be operated upon the highways not to exceed a five-mile radius of such auction by prospective purchasers only for the purpose of road testing without being inspected; motor vehicles, trailers, or semitrailers purchased from auto auctions within the Commonwealth also may be operated upon the highways from such auction to the purchaser's place of residence or business without being inspected;

12. Motor vehicles, trailers, or semitrailers, after the expiration of a period fixed for the inspection thereof, may be operated over the most direct route between the place where such vehicle is kept or garaged and an official inspection station for the purpose of having the same inspected pursuant to a prior appointment with such station;

13. Any vehicle for transporting well-drilling machinery and mobile equipment as defined in § 46.2-700 of the Code of Virginia;

14. Motor vehicles being towed in a legal manner as exempted under § 46.2-1150 of the Code of Virginia;

15. Logtrailers as exempted under § 46.2-1159 of the Code of Virginia;

16. Motor vehicles designed or altered and used exclusively for racing or other exhibition purposes as exempted under § 46.2-1160 of the Code of Virginia;

17. Any tow dolly or converter gear as defined in § 46.2-1119 of the Code of Virginia;

18. A new motor vehicle, as defined in § 46.2-1500 of the Code of Virginia, that has been inspected in accordance with an inspection requirement of the manufacturer or distributor of the new motor vehicle (i.e., predelivery inspection (PDI)) by an employee who customarily performs such inspection on behalf of a motor vehicle dealer licensed pursuant to § 46.2-1508 of the Code of Virginia shall be deemed to have met the safety inspection requirements of the this section without a separate safety inspection by an official inspection station. Such inspection shall be deemed to be the first inspection for the purpose of § 46.2-1158 of the Code of Virginia, and an inspection approval sticker furnished by the Department of State Police at the uniform price paid by all official inspection stations to the Department of State Police for an inspection approval sticker may be affixed to the vehicle as required by § 46.2-1163 of the Code of Virginia.

NOTE: Only an active certified safety inspector may enter the vehicle's information into the Motor Vehicle Inspection Program (MVIP) database and affix the inspection sticker to the vehicle;

19. Mopeds;

20. Low-speed vehicles; and

21. Vehicles exempt from registration pursuant to Article 6 (§ 46.2-662 et seq.) of Chapter 6 of Title 46.2 of the Code of Virginia.

B. The following shall be exempt from inspection as required by § 46.2-1157 of the Code of Virginia provided (i) the commercial motor vehicle operates in interstate commerce; (ii) the commercial motor vehicle is found to meet the federal requirements for annual inspection through a self-inspection, a third-party inspection, a Commercial Vehicle Safety Alliance inspection, or a periodic inspection performed by any state with a program; (iii) the inspection has been determined by the Federal Motor Carrier Safety Administration to be comparable to or as effective as the requirements of 49 CFR 396.3(a); and (iv) documentation of such determination as provided for in 49 CFR 396.3(b) is available for review by law-enforcement officials to verify that the inspection is current:

1. Any commercial motor vehicle operating in interstate commerce that is subject to the Federal Motor Carrier Safety Regulations.

2. Any trailer or semitrailer being operated in interstate commerce that is subject to the Federal Motor Carrier Safety Regulations.

19VAC30-70-30

19VAC30-70-30. Inspector requirements. (Repealed.)

A. The inspection of motor vehicles required by these rules and regulations shall be made only by those individuals who are certified and licensed as safety inspectors by the Department of State Police. The procedures outlined in this section are applicable to the processing of applications for initial certification, reclassification of safety inspector's licenses, and reinstatement of suspended or revoked safety inspector's licenses.

B. All certified inspectors shall be at least 18 years of age. In addition, all certified inspectors shall have:

1. A minimum of one year of practical experience as an automotive mechanic or six months of practical experience as an automotive mechanic combined with an additional and separate six months of mirroring a certified state inspector, or

2. Satisfactorily completed a training program in the field of automotive mechanics approved by the Superintendent of State Police.

A person who has met either of the practical experience requirements in repairing motorcycles may be certified to inspect motorcycles only and a person who meets them in repairing trailers may be certified to inspect trailers only.

C. Each mechanic entering the inspection program will be required to satisfactorily pass a written and practical examination exhibiting his knowledge of the inspection procedures.

D. Each certified inspector shall possess a valid Virginia driver's license with the following exceptions:

1. An inspector who is a resident of an adjoining state holding a valid driver's license in that state and who commutes regularly to work in Virginia; or

2. A member of the armed forces of the United States on active duty, or a dependent thereof, who holds a driver's license from his home state.

E. An inspector whose driver's license is suspended or revoked, including the seven-day administrative suspension for a DUI arrest, must immediately notify the station's supervising trooper or the local Safety Division Area Office of the suspension or revocation. The suspension or revocation of an inspector's driver's license shall automatically act as a suspension of his privilege to inspect motor vehicles until such suspension or revocation is terminated and the reinstatement has been made by the Superintendent of State Police.

F. Each licensed safety inspector must have a valid safety inspector's license in his possession at all times while conducting inspections.

G. Each safety inspector with a valid safety inspector's license need only present such valid license to his new employer to commence participation in the program at his new place of employment. Management of the inspection station is required to notify the Safety Division when a safety inspector begins or ends employment. This may be handled by contacting the Safety Division Headquarters in Richmond by telephone.

H. An inspector must promptly notify the Safety Division in writing of any change in his home address as shown on the safety inspector's license. In the event the license becomes mutilated, lost or stolen, the inspector must notify the Department of State Police immediately in writing, requesting a duplicate. The Safety Inspector Notification Form shall be used and all requested information should be printed plainly and completely. For those inspectors who are not employed, write "Inactive" in the station name block. In those cases where notification is being made due to an address change, it will be necessary to: (i) fill out the form completely and (ii) retain a copy of the form and license until a permanent (new) license is received. In those cases where the license has been lost, stolen or mutilated, complete steps in clauses (i) and (ii) as set forth in this subsection. The notification form may be duplicated as necessary.

I. An inspector must immediately notify the station's supervising trooper or local Safety Division Area Office of an arrest for a criminal offense or the institution of a civil action.

J. Requirements for safety inspector applicants with a specific learning disability:

1. Applicants will be required to furnish documentation from the particular school division where the applicant was classified as having a learning disability. The specific learning disability will be clearly identified.

2. Once the learning disability has been documented, and if applicable, the applicant will be allowed to test with the written exam being orally presented.

3. The station management where the applicant is employed or to be employed must agree to have someone present during the hours the employee is conducting inspections to assist with the reading of the Official Motor Vehicle Safety Inspection Manual when necessary during the initial three-year certification period. If the inspector changes stations within the first three-year period, it is the inspector's responsibility to notify station management of his disability and this requirement.

19VAC30-70-31

19VAC30-70-31. Inspector certification. (Repealed.)

A. Upon request, a Mechanics Certification Application (Form SP-170B) and a Criminal History Record Request (Form SP-167) will be provided to individuals desiring appointment as certified safety inspectors.

1. The application package will include instructions to help guide the applicant through the process.

2. Applicants may be certified in any of the following classes after completing the necessary requirements and the appropriate examinations:

a. Class A – May inspect any motor vehicle, motorcycle, or trailer.

b. Class B – May inspect trailers only.

c. Class C – May inspect motorcycles only.

B. Applicants should immediately prepare for the written examination by studying the Official Motor Vehicle Safety Inspection Manual in its entirety.

1. When sufficiently prepared for the examination, the applicant should visit a testing site in his area to complete the appropriate examination.

2. The applicant will present his completed application Form SP-170B, a Criminal History Records Request (Form SP -167), and a valid driver's license at the testing site. The applicant's identity will be verified by comparing the driver's license to the application form. The application will be reviewed for proper notarization. The application shall include the applicant's name, address, date of birth, social security number, driver's license number, physical, personal, and employment data.

3. If the applicant's driver's license is expired, suspended, or revoked, the applicant will be advised and the application will be destroyed. The applicant may reapply after his driver's license is reinstated.

C. The Class A inspector examination will consist of five sections containing 20 questions each. A minimum score of 75% must be attained for each section. The Class B and C inspector examinations will consist of 50 questions each. A minimum score of 74% must be attained. If the applicant fails the test, it will be noted at the end of Section I on the Form SP-170B with the word "Failed" and the date. The application will be returned to the applicant. Applicants failing to attain the minimum score will not be allowed to test again for 30 days. Applicants failing a second or subsequent examination will not be allowed to test again for six months.

D. The Mechanics Certification Application (Form SP-170B) and Criminal History Record Request (Form SP-167) for applicants who achieve a minimum score or greater will be forwarded to Safety Division Headquarters.

1. The applicant's record will be checked against safety inspector and Central Criminal Records Exchange (CCRE) files.

2. Inspection and criminal record information along with the applicant's driver transcript will be forwarded with the application to the appropriate Safety Division Area Office for investigation.

3. A credit check will be performed to determine that the applicant associated with the inspection program is in compliance with any judgment order or is meeting all financial obligations, or both.

E. A background investigation will be conducted consisting of the following:

1. Verification that the applicant is at least 18 years of age.

2. Verification that the applicant has not less than one year's practical experience employed as an automotive technician repairing vehicles for the public or has satisfactorily completed a training program in the field of automotive mechanics approved by the Department of State Police. The following training programs in the field of automotive mechanics have been approved as a substitute for the one year's practical experience requirement:

a. The two-year Associate Degree or diploma programs in automotive technology offered by the Virginia Community College System consisting of the following minimum curriculum:

(1) Automotive Electrical Systems - 3 semester hours

(2) Braking Systems - 3 semester hours

(3) Emissions Control Systems - 3 semester hours

(4) Suspension and Steering Systems - 3 semester hours

(5) Vehicle Safety Inspection - 2 semester hours

b. The 1,080-hour Career Technical Automotive Services Technology Program, offered by the Office of Career Technical Education, State Department of Education, in the various technical schools located throughout Virginia or be certified by the National Institute for Automotive Service Excellence (ASE), or both.

(1) Upon the successful completion of this course, including a practical test as defined in this section, the student must complete a Mechanics Certification Application (Form SP-170B) and a Criminal History Record Request (Form SP-167), pass a written test as defined in subsection C of this section, and submit to a background investigation as defined in this subsection. Upon successful completion of these requirements, the student, if 18 years of age, will be certified as a safety inspector and issued a safety inspector license.

(2) If the student scores less than 75% on any part of the examination, the application will be returned to the certifying trooper. Students scoring less than 75% on any part of the examination may retest at the certifying trooper's next recertification testing date, but not sooner than 30 days from the date of the last examination. If the student passes the test at this time and is at least 18 years of age, he will be issued a safety inspector license. Upon the student's 18th birthday, providing he still meets all of the requirements, the student will be issued a safety inspector license.

(3) Students failing the second written examination will not be allowed to test again for six months. In order to retest the student must be at least 18 years of age and must complete the application process set forth for original certification.

c. The 1,500-hour Course #1 entitled "Auto-Diesel Technician Course" offered by the Nashville Auto Diesel College, Inc., 1524 Gallatin Road, Nashville, Tennessee 37206.

3. A determination of the applicant's mechanical ability through interviews with employers and customers.

4. A review of the applicant's current driving record on file with the Department of Motor Vehicles (DMV) will be utilized in determining applicant's suitability for certification.

5. Determination of the character and reputation of the applicant through previous associates, employers, and records.

6. Determination of the applicant's attitude towards the inspection program and receptiveness to State Police supervision through personal interview.

7. The investigating trooper shall administer a practical examination to determine the applicant's ability to conduct a safety inspection. The applicant will conduct a complete inspection including the use of the optical headlight aimer.

F. Any applicant whose application is rejected or withdrawn may not reapply sooner than six months from the date he is notified of the rejection of their application or their application is withdrawn.

G. When a safety inspector is certified, the bottom of the Form SP-170B will be completed by the certifying trooper. The classification for which the safety inspector is being certified, and the date of certification must be entered by the trooper on the bottom of the Form SP-170B. The Form SP-170B shall then be forwarded to the Safety Division Area Office.

H. Upon certification, the supervising trooper will fill out the temporary inspector's license in triplicate, forwarding the original (white copy) to Safety Division Headquarters, issuing the canary copy to the inspector, and retaining the pink copy at the Safety Division Area Office for six months. Once the safety inspector has been issued his temporary license, he will be eligible to begin inspecting.

I. All safety inspector licenses shall be valid for a period of three years.

19VAC30-70-32

19VAC30-70-32. Reinstatement of safety inspector license following suspension or revocation. (Repealed.)

A. Reinstatement of safety inspector licenses following a period of suspension or revocation.

1. Once a safety inspector's license has been suspended, regardless of the cause for suspension, he may request reinstatement up to 60 days prior to the expiration of the suspension period.

a. No application Form SP-170B is required for reinstatement; however, Form SP-170D and Form SP-167 must be completed. The safety inspector's license will be held at the local Safety Division Area Office and returned upon the expiration of the suspension period. In all cases, Safety Division Headquarters must be notified forthwith by electronic means of the reinstatement of the license. The Form SP-164 will be filed to indicate the date the inspector was reinstated.

b. The inspector shall contact his supervising trooper or nearest Safety Division Area Office to initiate the reinstatement process.

c. The inspector's records on file at the Department of Motor Vehicles and Central Criminal Records Exchange will be reviewed to determine his suitability for reinstatement. If the suspended inspector's records indicate he is suitable for reinstatement, at the end of the suspension period or other appropriate time, the original inspector's license will be returned. A temporary license may be issued if the original is not available.

If the suspended inspector's license should expire during the suspension period, the inspector may complete the process for inspector recertification as outlined in 19VAC30-70-9. The trooper administering the test will retain all documentation. The inspector's license will be returned at the end of the suspension period and the appropriate documents forwarded to the Safety Division.

2. Inspectors whose safety inspector's licenses have been revoked must complete the application process as set forth for initial certification after the expiration of the period of revocation.

B. Safety inspectors who desire to change their license classification must complete the written and practical examinations as outlined in 19VAC30-70-9.

C. Safety inspectors desiring to renew their inspector's license must participate in the recertification process. The process will require:

1. Review of training materials as may be presented at the certification testing site by State Police personnel.

2. Completion of the appropriate examination for the class license the inspector holds. A minimum score must be attained as previously outlined in 19VAC30-70-9.

3. An inspector holding an expired license may be tested as long as his license has not been expired more than one month. During the period of expiration he will not be permitted to perform inspections.

An inspector holding an expired inspector license which has not been expired more than one month and who fails the recertification examination the first time during this one-month grace period may be retested one additional time not sooner than 30 days from the date of the last recertification examination. Inspectors failing this subsequent examination will not be retested for six months and must complete the application process as set forth for initial certification.

D. Failure to comply with the provisions of this section shall be grounds for the termination of the application process or cancellation of the safety inspector's license, or both. Applicants having applications terminated or safety inspector's license canceled may not reapply for a period of one year.

19VAC30-70-40

19VAC30-70-40. Fees.

A. Before the inspection of a vehicle begins, the vehicle owner or operator must be informed that a charge is to be made there is a regulated fee pursuant to § 46.2-1167 of the Code of Virginia.

B. The maximum inspection fees effective July 1, 2006 2019, are as follows:

$51 for each inspection of any (i) tractor truck, (ii) truck that has a gross vehicle weight rating of 26,000 pounds or more, or (iii) motor vehicle that is used to transport passengers and has a seating capacity of more than 15 passengers, including the driver.

$12 for each inspection of any motorcycle and autocycle.

$16 for each inspection of any other vehicle, including trailers and motor homes.

1. Inspection fees will result in inspection stations retaining and forwarding $.50 to the Department of State Police to support the department's costs in administering the Motor Vehicle Inspection Program (MVIP). Collection of these fees will begin on March 15 of every year be billed quarterly to each station on April 15, July 15, October 15, and January 15 of each year.

Tractor Trucks

Trucks that have a gross vehicle weight rating of 26,000 pounds or more

Buses that seat more than 15 passengers (including the driver)

$.50 per inspection

Cars

Pickup Trucks/Trucks

Recreational Motor Homes

Trailers

$.70 per inspection

Motorcycles

Autocycles

$2.00 per inspection

2. $10 of the $12 inspection fee for motorcycles shall be retained by the inspection station and the other $2.00 shall be transmitted to the Department of State Police. Collection of these fees will begin March 15 of every year.

3. After the appropriate fee has been determined for each station, a letter from the Safety Division will be mailed to the station requiring that a check for that amount be mailed in the enclosed envelope to: Department of State Police, Safety Division, 7700 Midlothian Turnpike, North Chesterfield, VA 23235. The check must be made out to the Department of State Police. The letter will include the following notice: "Do Not Send The Processing Fee To The P.O. Box. All Fees Are To Be Sent To The Safety Division Street Address."

4. 2. After the appropriate fee has been determined for each station, an invoice is uploaded to each station's MVIP account. The procedures for mailing payments are outlined in this subdivision as follows:

a. Print the invoice from the MVIP station account.

b. Prepare a check, cashier's check, or money order made payable to the Department of State Police for the amount indicated on the invoice and include the station number within the memo section of the check.

c. Prepare an envelope with the following information: Department of State Police - Safety Division, P.O. Box 27472, Richmond, Virginia 23261.

d. Mail the check and invoice to the address listed in subdivision 2 c of this subsection.

3. The station will have has 30 days in which to mail in the processing fee. In the event a check does not clear the bank for any reason, a $15 $50 fee will be assessed the station. Also, under 19VAC30-70-5, a returned check will be a Class III offense and administrative actions may be held against the station's record. Once the station has been contacted by the Department of State Police regarding a returned check, it will have 15 days to respond. If the returned check dispute is not settled in this period of time, administrative or legal sanctions, or both, may be taken against the station and, in addition, any requests for supplies will not be honored until the dispute has been settled.

C. If a rejected vehicle is not submitted to the same station within the validity period of the rejection sticker or is submitted to another official inspection station, a complete inspection must be performed and a charge of $51 may be made for inspection of tractor trucks, trucks that have a gross vehicle weight rating of 26,000 pounds or more, and buses that seat more than 15 passengers, including the driver. A charge of $16 $20 may be made for each inspection performed on any other vehicle to include recreational motor homes and trailers. A charge of $12 may be made for each motorcycle and autocycle inspection.

NOTE: The truck inspection fee does not pertain to any trailer.

D. A charge of $1.00 may be made for reinspection of a vehicle rejected by the same station during the 15-day validity of the rejection sticker.

E. Inspection stations shall not charge an additional fee to those customers who drop off their vehicles for a state inspection. This is a violation of § 46.2-1167 of the Code of Virginia unless the station charges a "storage fee" for all services and repairs and not just for inspections.

19VAC30-70-50

19VAC30-70-50. Approval stickers and decals.

A. If the vehicle meets all inspection requirements, the certified safety inspector performing the inspection shall immediately enter the receipt information via the MVIP Motor Vehicle Inspection Program (MVIP) system.

The inspection sticker is not valid unless the rear portion is completed with the vehicle make, year built, license plate number (dealer name if a dealer tag is displayed), body type, and the complete vehicle identification number (VIN). The inspection sticker shall be completed using black indelible ink.

B. Approval stickers and decals shall be issued according to the following schedule:

ANNUAL PROGRAM

Vehicles inspected in January are issued stickers bearing the Number "1"
Vehicles inspected in February are issued stickers bearing the Number "2"
Vehicles inspected in March are issued stickers bearing the Number "3"
Vehicles inspected in April are issued stickers bearing the Number "4"
Vehicles inspected in May are issued stickers bearing the Number "5"
Vehicles inspected in June are issued stickers bearing the Number "6"
Vehicles inspected in July are issued stickers bearing the Number "7"
Vehicles inspected in August are issued stickers bearing the Number "8"
Vehicles inspected in September are issued stickers bearing the Number "9"
Vehicles inspected in October are issued stickers bearing the Number "10"
Vehicles inspected in November are issued stickers bearing the Number "11"
Vehicles inspected in December are issued stickers bearing the Number "12"

All issued annual inspection stickers shall expire at the end of the last day of the month displayed on the sticker. For example, a January inspection sticker expires at 12:00:00 a.m. on February 1.

All February annual inspection stickers for trailer and motorcycle decals (#2) (i.e., stickers numbered "2") due to expire at midnight, February 28 automatically will be valid through midnight February 29 each leap year.

C. The numeral decal insert indicating the month of expiration shall be inserted in affixed to the box identified as month and the numeral decal indicating the year of expiration shall be inserted in the box identified as year of on the car or truck approval sticker. The numeral insert indicating the month and year of expiration shall be affixed to the box identified as month and year on the trailer or motorcycle sticker.

Extreme care should be used by inspectors in when applying these inserts. On all windshields, the The sticker is to shall be placed at the bottom left corner of the windshield when viewed from the inside of the vehicle. The left edge of the sticker is to be placed as close as practical, but no closer than one inch to the left edge of the windshield when viewed from the inside of the vehicle. The top edge of the sticker is to be approximately four inches from the bottom of the windshield when viewed from the inside of the vehicle.

NOTE: Minor adjustments to the placement of the safety inspection sticker may be made to avoid the decal being obscured by the windshield's monogram.

NOTE: On passenger vehicles not equipped with a windshield, the sticker shall be placed on or under the dash and protected in some manner from the weather.

EXCEPTIONS: On vehicles equipped with heating and grid elements on the inside of the windshield, the sticker shall be placed one inch above the top of the grid element and the left edge of the sticker shall be approximately one inch to the right of the left edge of the windshield when viewed from the inside of the vehicle.

Any sticker or decal required by the laws of any other state or the District of Columbia and displayed upon the windshield of a vehicle submitted for inspection in the Commonwealth is permitted by the superintendent, provided the vehicle is currently registered in that jurisdiction, and the sticker is displayed in a manner designated by the issuing authority and has not expired. In these cases, if the sticker or decal is located where the inspection sticker is to be placed, it will not be removed unless the owner or operator authorizes its removal. The inspection sticker will be placed 1/4 inch to the right of the sticker or decal when viewed from the inside of the vehicle without removing or overlapping the sticker or decal.

D. The Code of Virginia requires that the inspection sticker be displayed on the windshield or at other designated places at all times. The inspection sticker cannot be transferred from one vehicle to another.

EXCEPTION: If the windshield in a vehicle is replaced, a valid sticker may be removed from the old windshield and placed on the new windshield.

E. The sticker issued to a motorcycle shall be affixed to the left side of the cycle where it will be most visible after mounting. The sticker may be placed on a plate on the left side where it will be most visible and securely fastened to the motorcycle for the purpose of displaying the sticker. The sticker may be placed horizontally or vertically.

F. Trailer stickers will be issued to all trailers and semitrailers required to be inspected. (No boat, utility, or travel trailer that is not equipped with brakes shall be required to be inspected.)

G. All inspected trailers must display a trailer sticker on that particular vehicle. These stickers are to be placed on the left side of the trailer near the front corner. The sticker must be affixed to the trailer body or frame. In those instances where a metal back container with a removable transparent cover has been permanently affixed to the trailer body, the sticker may be glued to it. The container must be permanently mounted in such a manner that the sticker must be destroyed to remove it.

H. In all other cases involving unusually designed trailers such as pole trailers, the safety inspector is to exercise his own good judgment in placing the sticker at a point where it will be as prominent as possible and visible for examination from the left side.

I. Motorcycles have a separate sticker that is orange and issued with the prefix M. Trailers have a separate sticker that is blue and issued with the prefix T. The trailer and motorcycle receipts are completed in the same manner as other inspection receipts.

J. Appointed stations will keep sufficient inspection supplies on hand to meet their needs. Requests for additional supplies shall be ordered via the MVIP system. Requests for supplies that are to be picked up at the Safety Division Headquarters must be made at least 24 hours prior to pick up.

Packing slips mailed with inspection supplies will be kept on file at the station for at least 24 months.

K. All unused center inserts used to indicate the month that a sticker expires, in possession of the inspection station at the end of each month, shall be retained by the inspection station, properly safeguarded, and used in the inspection of vehicles for that particular month in the following year or be disposed of as directed by the Department of State Police.

All inspection supplies that are voided, damaged, disfigured or become unserviceable in any manner, will be returned to the Safety Division. New replacement supplies will be issued to the station. Expired stickers will be picked up by the station's supervising trooper.

L. All voided approval or rejection stickers will be picked up by the station's supervising trooper.

M. The MVIP system approval or rejection printed receipt shall be given to the owner or operator of the vehicle. In the event of an MVIP or internet connection failure, manual receipts from the approval and rejection books shall be utilized.

N. All yellow white copies of approval stickers will within the approval (car and truck, trailer and motorcycle) and rejection books shall be retained in the books and shall be kept on file at the station for at least six months. Stations shall notate necessary information on the white copy to provide a means of tracking for audit purposes. They may be inspected by any law-enforcement officer during normal business hours.

O. Safety Division troopers may replace inspection stickers that have separated from the windshield of motor vehicles and become lost or damaged without conducting an inspection of the safety components of the vehicle. Such replacement of inspection stickers shall be made only in accordance with the following provisions:

1. A vehicle owner or operator complaining of the loss or damage to the inspection sticker on the windshield of their vehicle due to separation of the sticker from the windshield shall be directed to the nearest Safety Division Area Office or Safety Division trooper.

2. Safety Division troopers, upon receipt of a complaint from a vehicle owner or operator that their inspection sticker has been stolen, lost or become damaged due to separation from the windshield, will make arrangements to meet the person to effect the replacement of the sticker. A vehicle owner or operator alleging theft of the inspection sticker will furnish proof to the Safety Division trooper that such theft has been reported to the proper law-enforcement authority.

3. The vehicle owner or operator must produce the original safety inspection approval sticker receipt indicating a valid approval inspection sticker was issued to the vehicle within the past 11 months. (The vehicle must be reinspected if the expiration of the original inspection sticker is in the month the request is being made.)

4. The Safety Division trooper will verify by the inspection receipt that the vehicle was issued an approval inspection sticker within the past 11 months and will then issue a replacement inspection sticker to the vehicle. If any obvious equipment defects are detected during the replacement process, the vehicle will not be issued a replacement approval sticker.

5. The Safety Division trooper will complete the inspection sticker receipt for the approval sticker from information contained on the original receipt. The date the replacement sticker is issued will be used in the date space. In the space for Inspection Related Charges, the trooper will insert the word "REPLACEMENT" and the sticker number from the original inspection receipt.

6. The Safety Division trooper will sign the receipt vertically in the O.K. column in the "Equipment Inspected" blocks. These blocks will not otherwise be completed.

7. The Safety Division trooper shall place month and year inserts on the inspection sticker to reflect the expiration as shown on the original approval inspection sticker and place the inspection sticker on the windshield in accordance with the requirements of subsection C of this section.

8. The Safety Division trooper will enter the replacement information into the MVIP system.

P. New vehicle safety inspections.

1. Section 46.2-1158.01 of the Code of Virginia allows an employee who customarily performs the inspection requirement of a manufacturer or distributor of new motor vehicles to place an inspection sticker furnished by the Department of State Police on the vehicle once it has met the requirements of that manufacturer or distributor. This employee does not have to be a certified safety inspector.

2. With the addition of other personnel using Department of State Police inspection supplies, a system shall be developed at each inspection station to afford accountability of all supplies. The system shall include proper safeguards to prevent the loss of supplies through carelessness, neglect, theft, or unauthorized use.

3. Inspection stations shall not mix annual state inspections with predelivery inspections (PDI) in the same book of inspection stickers.

4. All employees shall be reminded that anyone who performs inspections, whether it be for the annual inspection or the PDI inspection, is subject to criminal prosecution if inspection supplies are used illegally or used in some other unauthorized way.

5. Station management and licensed safety inspectors are subject to administrative sanctions for any misuse of inspection supplies.

6. The inspection receipts shall be completed as usual with the following exceptions: On the "inspector" line, the initials "PDI" (for predelivery inspection) and the printed employee's name performing the inspection shall be entered. On the "inspector's license number" line, the letters "N/A" shall be entered. In the equipment inspected section, the words "New Vehicle" shall be entered in the "adjust" column. The PDI employee performing the inspection shall sign his name in the "O.K." column.

19VAC30-70-80

Part III
Inspection Requirements for Passenger Vehicles and Vehicles Up to 10,000 Pounds (GVWR)

19VAC30-70-80. Service brakes.

A. The inspector, as a minimum, must drive all vehicles into the inspection lane and test both service and parking brakes.

B. A minimum of two wheels or two wheels and drums, one front and one rear, must be removed from inspected on each passenger and multipurpose vehicle with a gross vehicle weight rating of 10,000 pounds gross vehicle weight rating (GVWR) or less at the time of inspection, except those listed in subdivisions 1, 2, and 3 of this subsection. Two front wheels or two front wheels and drums must be removed from vehicles listed in subdivision 3 of this subsection.

NOTE: If the vehicle is equipped with wheels that do not allow visual access to the braking system, the inspected wheels shall be removed.

NOTE: If the vehicle is equipped with drum brakes, the wheel and drum shall be removed for inspection.

1. Motorcycles.

2. A new model vehicle is defined as a vehicle that has not been titled or leased and is less than one year old, measured from October 1 as of each year; if such motor vehicle does not have a model year, such measurement shall be made from the date of manufacture.

3. Trucks with floating axles that require seal replacement upon removal of rear wheels. The inspection receipt (approval and rejection) shall be marked to reflect which wheels were pulled.

Warning: Lug If wheels are removed to inspect brakes, lug nuts must be torqued to the manufacturer's specifications to prevent damage to disc rotors. The use of an impact wrench may exceed the manufacturer's specifications and damage disc rotors.

C. If any braking problem is detected, the inspector may test drive or require a test drive of the vehicle.

D. Inspect for and reject if:

1. Vehicle is not equipped with brakes or any brake has been disconnected, rendered inoperative, or improperly installed. Trailers having an actual gross weight of less than 3,000 pounds are not required to be equipped with brakes; however, if brakes are installed, these vehicles must be inspected.

Brake System Failure Indicator Lamp

2. Passenger vehicles manufactured after January 1, 1968, are not equipped with a red brake failure warning lamp or warning lamp does not light with parking brake applied when ignition key is turned to the start position, except for anti-lock system. The red brake failure warning lamp should light when the ignition key is turned to the start position; on some imports it may be checked when the emergency brake is applied or other factory installed test button. (DO NOT reject if only the amber ABS/anti-lock brake lamp is on.) With the engine running and parking brake released, the red brake failure warning lamp should go off, except for vehicles equipped with anti-lock system. If so, apply service brake for 10 seconds and if the red brake failure warning lamp lights again the system is defective. Also, if the warning lamp light does not come on when there is a leak or the warning lamp light is not functioning properly, the system is defective and shall be rejected. NOTE: This paragraph subdivision does not apply to vehicles registered as street rods nor does it imply that the red brake failure warning lamp needs to light when the emergency brake is set. There are many vehicles that are not factory equipped with an emergency brake indicator light.

Note: Vehicles equipped with a brake pad wear indicator warning light shall not constitute an automatic rejection for the vehicle submitted for a safety inspection. Each vehicle manufacturer has determined an appropriate level to activate the brake pad wear indicator warning light; therefore, it shall be the responsibility of the inspector to confirm whether or not the brake pads have exceeded the established tolerance of 2/32 of an inch.

Brake Linings and Disc Pads

3. Riveted linings or disc pads are worn to less than 2/32 of an inch over the rivet head(s) heads.

4. Bonded or molded linings or disc pads are worn to less than 2/32 of an inch in thickness.

5. Wire in wire-backed lining is visible in friction surface.

6. Snap-on brake linings are loose.

7. Any lining is broken or cracked so that the lining or parts of the lining are not firmly attached to the shoe or has cracks on the friction surface extending to the open edge.

8. Grease or other contamination is present on the linings, drums, or rotors.

9. Rivets in riveted linings are loose or missing.

10. Any lining or pad is misaligned or does not make full contact with the drum or rotor.

Brake Drums and Discs

NOTE: The inspector shall ensure that the minimum measurements in subdivisions D 3 and D 4 of this section are obtained.

11. Brake drums or brake discs (rotors) are worn or scored to the extent that their machining would result in a failure to meet manufacturer's specifications. Use the specification stamped on the rotor or drum if available.

NOTE: A number of vehicles on the market are equipped with a lock nut to hold the rear brake drum in place. Manufacturers recommend replacement of these lock nuts after each removal to prevent failure of the component. If the customer is advised up front, then the wholesale cost of the replacement nut may be charged to the customer.

NOTE: The proper method to remove the rear brake assembly on the 2000 Ford Focus is to remove the four bolts from the opposite side of the assembly. Removal otherwise may damage the outside grease cap and incur a cost to replace.

12. Brake drums or discs have any external crack or cracks more than one half the width of the friction surface of the drum or disc. NOTE: Do not confuse short hairline heat cracks with flexural cracks.

Mechanical Linkage

13. Cables are frayed or frozen.

14. Mechanical parts missing, broken, badly worn, or misaligned.

E. Hydraulic.

NOTE: Some motor vehicles, beginning with 1976 models, have a hydraulic power system that serves both the power-assisted brakes and power-assisted steering system. Some vehicles, beginning with 1985 models, have an integrated hydraulic actuation and anti-lock brake unit using only brake fluid.

1. Brake hydraulic system. Inspector should check the brake hydraulic system in the following manner: test vehicle in a standing position; apply moderate pressure to the brake pedal for 10 seconds. Brake pedal height must be maintained. On vehicles equipped with power-assisted systems, the engine should be running.

2. Hydraulic system operation. Stop engine, then depress brake pedal several times to eliminate all pressure. Depress pedal with a light foot-force (30 pounds). While maintaining this force on the pedal, start engine and observe if pedal moves slightly when engine starts.

Reject vehicle if pedal does not move slightly as engine is started while force is on brake pedal.

 http://leg5.state.va.us/images/399187778352VSPRE_files/image001.gif

3. Condition of hydraulic booster power brake system. Inspect system for fluid level and leaks.

Reject vehicle if there is insufficient fluid in the reservoir; if there are broken, kinked or restricted fluid lines or hoses; if there is any leakage of fluid at the pump, steering gear or brake booster, or any of the lines or hoses in the system; or if belts are frayed, cracked or excessively worn.

4. Integrated hydraulic booster/anti-lock system operation. With the ignition key in the off position, depress brake pedal a minimum of 25 times to deplete all residual stored pressure in the accumulator. Depress pedal with a light foot-force (25 pounds). Place ignition key in the on position and allow 60 seconds for the brake warning light to go out and the electric pump to shut off.

Reject vehicle if the brake pedal does not move down slightly as the pump builds pressure or if the brake and anti-lock warning lights remain on longer than 60 seconds.

NOTE: The inspection of the ABS light is only for an integrated system that is an earlier system. The newer system that has the nonintegrated systems does not need to be checked. If the ABS system malfunctions on the newer system, the brake systems are still functional.

 http://leg5.state.va.us/images/399187778352VSPRE_files/image002.gif

5. Condition of integrated hydraulic booster/anti-lock system with electronic pump. With the system fully charged, inspect system for fluid level and leaks.

Reject vehicle if there is insufficient fluid in the reservoir; if there are broken, kinked or restricted fluid lines or hoses; or if there is any leakage of fluid at the pump or brake booster, or any of the lines or hoses in the system.

6. Vacuum system operation. Stop engine then depress brake pedal several times to eliminate all vacuum in the system. Depress pedal with a light foot-force (25 pounds). While maintaining this force on the pedal, start engine and observe if pedal moves down slightly when engine starts.

Reject vehicle if pedal does not move down slightly as engine is started while force is on the brake pedal. In full vacuum-equipped vehicles, there is insufficient vacuum reserve for one full service brake application after engine is stopped.

 

 http://leg5.state.va.us/images/399188345722VSPRE_files/image001.gif

7. Condition of vacuum booster power brake system. Reject vehicle if there are collapsed, cracked, broken, badly chafed or improperly supported hoses and tubes, loose or broken hose clamps.

F. Inspect for and reject if:

General Specifications - Hydraulic Brakes

1. There is any leakage in the master cylinder, wheel cylinders, or brake calipers. When checking for leakage in rear wheel cylinders, do not disturb the dust boot.

NOTE: Do not reject for the common dust ball formed on wheel cylinders or for wetness that may have spread to the backing plate unless it has contaminated the linings or drums as specified in subdivision D 8 of this section. Consumers should be advised of this wear so that they will be aware that repair may be needed before their next inspection. This may not warrant an immediate repair considering the dual valve master cylinder.

2. Fluid level in master cylinder is below the proper level for the particular vehicle.

3. There is any evidence of a caliper sticking or binding.

Electric Brake System

4. Trailers show an amperage value more than 20% above or 30% below the brake manufacturer's maximum current rating for each brake.

5. Amp meter shows no reading or indicator is not steady on application and release of brake controller.

6. Any terminal connections are loose or dirty; wires are broken, frayed, or unsupported; any single conductor nonstranded wire or wires below the size recommended by the brake manufacturers are installed.

7. Electrical trailer brakes do not apply automatically when the breakaway safety switch is operated.

8. Breakaway braking devices are missing or inoperative; cable is frayed or broken.

General Specifications

9. Absence of braking action on any wheel required to have brakes.

10. There is any leakage in any hydraulic, air, or vacuum lines; hoses have any cracks, crimps, or restrictions or are abraded, exposing inner fabric; tubing or connections leak or are crimped, restricted, cracked, or broken; or any valves leak or are inoperative.

a. Reject the vehicle if the brake hoses or tubing are stretched or extended and do not allow for suspension movement.

b. Brake tubing and hoses must be:

(1) Long and flexible enough to accommodate without damage all normal motions of the parts to which they are attached;

(2) Secured against chaffing, kinking, or other mechanical damage; and

(3) Installed in a manner that prevents them from contacting the vehicle's exhaust system or any other source of high temperatures.

11. Any hydraulic brake tubing has been repaired using a compression fitting.

12. Brakes are not equalized so as to stop the vehicle on a straight line.

13. There is less than 1/5 reserve in actuator travel of the service brake when fully applied on all hydraulic, mechanical, or power-assisted hydraulic braking systems.

14. When tested on dry, hard, approximately level road free from loose material, at a speed of 20 miles per hour without leaving a 12-foot wide lane, results in excess of the following distances are obtained:

(When in doubt about a vehicle's stopping ability, the inspector shall conduct a road test.)

a. Any motor vehicle (except motorcycles, trucks, and tractor-trucks with semitrailers attached) four wheel brakes - 25 feet.

b. Any motor vehicle (except motorcycles, trucks, and tractor-trucks with semitrailers attached) two wheel brakes - 45 feet.

c. All combinations of vehicles - 40 feet.

19VAC30-70-90

19VAC30-70-90. Brakes: emergency, parking, or holding; batteries.

A. Some vehicles are equipped with an actual emergency brake, while others have only a parking or holding brake. Some types may be actuated by a foot or hand lever, while others may incorporate a switch or valve to actuate the brake. Air and vacuum brake systems may employ spring activating parking brakes.

B. Inspect for and reject if:

1. Vehicle or combination of vehicles is not equipped with a parking, holding, or emergency brake in good working order of the type installed as original standard factory equipment for the vehicle on which it is installed.

2. The parking brake actuating mechanism does not fully release when the control is operated to the off position or if the parking brake lamp light remains on.

NOTE: The light does not apply to vehicles that are not equipped with a parking (emergency) brake indicator light.

3. Any mechanical parts are missing, broken, badly worn, or are inoperative.

4. Cables are stretched, worn, or frayed or not operating freely.

5. Grease or similar-type contamination is present on the linings, drums, or rotors.

6. Parking brake will not hold the vehicle stationary with the engine running at slightly accelerated speed with shift lever in drive position for automatic transmission or shift lever in low gear with clutch engaged for standard shift transmission.

7. Holding brake will not disengage when engine is started and vehicle is placed in drive. Holding brake will not hold vehicle stationary with foot on holding brake and vehicle in drive.

8. On vehicles equipped with automatic transmissions, the vehicle will start in any gear other than (P) park and (N) neutral. If the gearshift indicator does not identify the park (P) and neutral (N) positions, then the vehicle shall be rejected.

9. On vehicles equipped with manual transmissions, the vehicle will start in any gear if the clutch is not depressed or disengaged.

NOTE: This will not apply to older model vehicles, which were not originally equipped with a neutral-safety switch, clutch disengagement system or clutch pedal position sensor by the manufacturer.

10. The accelerator does not disengage after being depressed, allowing the engine to return to a normal idle speed.

C. Battery mounting and storage. Inspect for and reject if:

1. A battery is not securely attached to a fixed part of the motor vehicle or trailer. A battery is not protected by a removable cover or enclosure if the battery is installed in a location other than the engine compartment.

2. All brackets, hardware, bolts, and bushings used for securely mounting the battery to the vehicle are not present.

3. Removable covers or enclosures are not substantial and are not securely latched or fastened.

4. The battery compartment does not have openings to provide ample battery ventilation and drainage.

5. Whenever the cable to the starting motor passes through a metal compartment, the cable shall be protected against grounding by an acid and waterproof insulating bushing.

6. Whenever a battery and a fuel tank are both placed under the driver's seat, (i) the battery and fuel tank are not partitioned from each other or (ii) each compartment is not provided with an independent cover, ventilation, and drainage.

19VAC30-70-110

19VAC30-70-110. Steering and suspension.

A. The steering and suspension systems installed and utilized on motor vehicles have evolved to where many different suspension systems are being designed, developed, and employed on vehicles. To properly inspect the steering and suspension on vehicles, it may be necessary for the inspection to be made in accordance with manufacturer's recommended procedures in addition to meeting any requirements outlined in this regulation.

B. Inspect for and reject if:

1. Any modification has been made that affects normal functioning of the shock absorbers. The inspector should operate the vehicle when in doubt. (If there is no evidence of the convolutions (coils) of the spring hitting one another, one pair (two) of nonmetallic coil spring stabilizers may be present in each of a vehicle's front coil springs, provided the installation of the stabilizers does not cause the springs to be higher than their original height.)

Shock absorbers in fully extended or compressed positions when the vehicle is stationary will not function normally.

2. The front end suspension has been modified by the use of lift blocks. (A lift block is defined as any solid piece of wood, metal, or other material placed between and separating the vehicle's front axle and the springs.) This does not prohibit the use of shims that may be necessary to correct front end alignment.

3. Any modification has been made to the front end suspension which reduces turning radius, bypasses safety components of original steering mechanism or if there is any lateral movement between the axle and frame.

4. Any modification has been made to the suspension to cause the vehicle body or chassis to come in contact with the ground or expose the fuel tank to damage from collision.

Reject the vehicle if it has been modified by any means so as to raise its body more than three inches above the manufacturer's attachment points or the frame rail (exclude original manufacturer's spacers, washers or bushings when measuring).

5. Any modification has been made to cause the wheels to come in contact with the body or frame under normal operating conditions.

6. A motor vehicle has a repair kit or preventive maintenance kit installed on a tie rod end, idler arm, ball joint, or any other part of the vehicle's steering gear.

NOTE: The repair kit or preventive maintenance kit usually consists of a small coil spring and a plastic cap that is placed over the bolt stud of the component and held in place by a retaining nut. There is nothing in this paragraph that prohibits the replacement of parts or components of a motor vehicle's steering gear in order to correct deficiencies in the steering gear.

7. When checked visually, the wheels appear to be out of line or an axle is bent.

8. Any vehicle that shimmies or wanders at normal operating speeds.

9. Rack and pinion steering bellows (boot) is defective or missing. Do not inspect CV constant-velocity (CV) boots, CV joints, or universal joints on rear wheel drive vehicles.

NOTE: CV boots on the vehicle shall not be rejected if the CV boots are defective or missing.

10. Power steering is defective and affects adequate steering of the vehicle or power steering fluid in reservoir is below operating level, or if there is an obvious leak of power steering fluid. Do not reject for dampness.

NOTE: If the vehicle is equipped with power steering, the engine must be running during testing.

11. Power steering hoses have any cracks, crimps, or restrictions or are abraded, exposing inner fabric; tubing or connections leak or are crimped, restricted, cracked, or broken. Power steering tubing and hoses must be secured against chaffing, kinking, or other mechanical damage and be installed in a manner that prevents contact with the vehicle's exhaust system or any other source of high temperatures.

12. Power steering belt does not have sufficient tension, is frayed, or missing. The serpentine belt should only be rejected if a chunk of the ribbing is missing or a deep cut or crack exposes the inner fabric of the belt. (Do not reject for the many little surface cracks that appear in the ribs or back.)

13. Any modification has been made to any part of the steering or suspension system that affects proper steering or suspension or any part of the original suspension system has been disconnected.

NOTE: "All thread rod material" shall not be used as U-bolts in the suspension system.

Vehicles registered as street rods may substitute any part of the original suspension system provided the components are installed in accordance with the component manufacturers' specifications.

14. Any modification or replacement has been made to the steering wheel that affects proper steering. The steering wheel shall be rejected if the outside diameter is less than 13 inches unless original factory equipment.

15. Steering column has any absence or looseness of bolts or positioning parts, resulting in motion of the steering column from its normal position.

16. A spring is broken, sagging or misaligned, shackles are worn or loose, or if air bags are collapsed or the air suspension system leaks or is deflated.

CAUTION: Underneath inspection of a vehicle equipped with air suspension with excessive leak down could result in serious personal injury.

17. Shock absorbers or cross stabilizer links are disconnected, broken, bent, loose, or do not function properly on vehicles with this design.

18. Any front or rear axle or suspension positioning parts are cracked, broken, loose, worn, bent or missing, resulting in shifting of an axle from the normal position. Any control arm or suspension positioning part using bushings for control, support and normal functioning is deteriorated, damaged or missing the bushing, or the bushing is worn to the extent that the component can be moved by hand along the axis of the component.

NOTE: All rear suspension parts including but not limited to control arms (upper and lower ball joints, radius or torque arms, stabilizer bars, and trailing arms) shall not have any damage or noticeable play when checked with hand pressure.

19. A MacPherson strut installed on a motor vehicle is broken, bent, loose or does not function properly.

NOTE: Do not reject a shock absorber or MacPherson strut unless there is evidence of leakage that causes the device not to function properly.

20. If vehicles measured movement at top or bottom of tire is greater than:

 

Wheel Size:

less than 17 inches -

1/4 inch

 

 

17 to 18 inches -

3/8 inch

 

 

over 18 inches -

1/2 inch

 

 http://leg5.state.va.us/images/399189266526VSPRE_files/image001.gif

 

Proper lifting for wheel bearing, steering linkage looseness, and king pin play action

 

FIGURE A

FIGURE B

FIGURE C

NOTE: King pin play. If vehicle is equipped with king pins, first eliminate all wheel bearing movement by applying service brake. With front end lifted as illustrated for inspecting wheel bearings (Figure C), grasp the tire at the top and bottom and attempt to move it in and out to detect looseness. Measure the movement at the top or bottom of the tire at the outer circumference.

C. Wheel bearing/steering linkage.

Reject vehicle if any wheel bearing is excessively worn or not properly adjusted; any cotter key or other locking device is missing or inoperative.

NOTE: Lifting techniques vary for measuring wheel bearing movement. On vehicles with coil spring or torsion bar on lower support arm - hoist at frame (Figure A). On vehicles with coil spring on upper support arm - hoist at lower support arm (Figure B). On front wheel drive vehicles, the inspector must consult manufacturer's lifting information.

NOTE: With vehicle lifted properly, grasp tire at top and bottom, rock in and out and record movement. Wheel bearing looseness is detected by the relative movement between the brake drum or disc and the braking plate or splash shield.

CAUTION: If air suspension vehicles are hoisted via body support area, air spring damage may occur if the air suspension switch is not turned off. Reject vehicle if relative movement between drum and backing plate (disc and splash shield) is more than 1/8 inch measured at the outer circumference of the tire. 

D. Steering linkage play.

1. Reject vehicle if measured movement at front or rear of tire is greater than:

 

Wheel Size:

16 inches or less -

1/4 inch (6.5mm)

 

 

17 to 18 inches -

3/8 inch (9.5mm)

 

 

over 18 inches -

1/2 inch (13mm)

 

 http://leg5.state.va.us/images/399189266526VSPRE_files/image002.gif

NOTE: First eliminate all wheel-bearing movement by applying service brake. With vehicle lifted as shown in the diagram and wheels in straight-ahead position, grasp front and rear of tire and attempt to move assembly right and left without moving the steering gear.

2. Reject vehicle if the steering mechanism is unusually tight or binding when turning the steering wheel completely to the left or right or the steering mechanism will not turn in both directions stop to stop.

3. Reject vehicle if the steering stops have been removed or adjusted in so that steering radius is reduced.

E. Steering lash/travel. Reject vehicle if inspection reveals excessive wear and/or or looseness in any ball stud, end assembly, pivot point, mechanical linkage and/or or if steering gear box has any loose or missing bolts, or excessive wear, and/or or looseness is found at any other location in the steering that adversely affects the steering of the vehicle.

NOTE: For vehicles equipped with power steering, the engine must be running and the fluid level, belt tension and belt condition must be adequate before testing.

With road wheels in straight ahead position, turn steering wheel until motion can be detected at the front road wheels. Align a reference mark on the steering wheel with a mark on a ruler and slowly turn steering wheel in the opposite direction until motion can again be detected at the front road wheel (see diagram). Measure lash at steering wheel. Special lash-checking instruments may be used to measure free play in inches or degrees. Such instruments should always be mounted and used according to the manufacturer's instructions. Reject vehicle if steering wheel movement exceeds:

Power - 2 inches

Manual - 3 inches

Rack & Pinion - (Power or Manual) - 0.4 inch - see note

NOTE: No play is permissible for Volkswagen and Audi vehicles - consult respective manufacturer's specifications.

19VAC30-70-120

19VAC30-70-120. Frame, engine mounts, coupling devices and emergency chains.

Inspect for and reject if:

1. Frame or unitized (monocoque) body of any motor vehicle, trailer or semitrailer is possesses one or more of the following defective characteristics: rust holes; any area of the frame or its components is broken, cracked, sagging, or bent; or damaged at any location, including to include any welded joint or is rusted or; the frame is corroded to the point the frame where it is weakened as to reasonably constitute a hazard during the operation of the vehicle; or any holes are drilled in the top or bottom rail flanges of the frame or the frame or cross-member (except as specified by the manufacturer).

NOTE: Any welded repair of the frame must be in accordance with the vehicle manufacturer's recommendations.

NOTE: All sections of a unitized frame are considered stress-bearing to include pinch and side rails, floors, and all support framework.

2. Engine or transmission mounts and hardware is broken or missing. This includes all hardware bolts and bushings used for mounting to the vehicle's frame, engine, or transmission. Any engine or transmission mount shall be rejected if they allow the power train to come in contact with the firewall or other body parts. Any body, truck bed, or bumper mounts or mounting hardware shall be rejected if they do not properly secure these components to the frame as originally designed.

3. Trailer hitch or pintle hook is not securely attached. Reject if the pintle eye or trailer drawbar has any cracks or if any welding repairs have been made to the pintle eye.

4. Chains, cables, etc., used to attach a towed vehicle are not securely attached or are broken, worn or abraded.

5. Fifth wheel does not lock in position or have a locking mechanism in proper working order.

6. Fifth wheel assembly system has any leak of fluid or air.

7. Fifth wheel has any broken, missing, or damaged parts; or is not securely attached to the frame.

8. Trailer king pin is not secure, or is broken or worn so as to prevent secure fit in fifth wheel.

9. Any movement is detected at any location where any device has been placed between the body and the chassis.

10. Trailer is not equipped with an emergency chain or steel cable.

NOTE: Fifth wheel assembly system does not require an emergency chain or cable. A fifth wheel is defined as a device which interfaces with and couples to the upper coupler assembly of a semitrailer. The upper coupler assembly is a structure consisting of an upper coupler plate, king pin and supporting framework which interfaces with and couples to a fifth wheel. Ball and socket connections also referred to as hitch and coupling connections are not fifth wheel assemblies and do require an emergency chain or steel cable.

19VAC30-70-130

19VAC30-70-130. Tires; wheels; rims.

Inspect for and reject if:

1. Any tire is marked specifically for use other than on the highway such as "For Farm Use Only," "For Off-Highway Use Only," "For Mobile Home Use Only," or "For Trailer Use Only."

EXCEPTION: "For Trailer Use Only" tires are allowed when installed on trailers only.

2. A radial tire is mismatched on the same axle with a bias ply tire or a bias belted tire.

3. Bias ply or bias belted tires are used on the rear axle when radial ply tires are used on the front axle.

EXCEPTION: On a two-axle vehicle equipped with truck tires with 20-inch rim diameter and larger, bias or radial tires may be used on either axle if the vehicle has dual rear wheels or is equipped with wide-base single tires.

4. A vehicle has installed on any axle a space saver emergency spare tire that is intended for temporary use.

5. Any motor vehicle, trailer or semitrailer, except the dual wheels installed on motor vehicles having seats for more than seven passengers (i) operated wholly within a municipality or (ii) operated by urban and suburban bus lines, which are defined as bus lines operating over regularly scheduled routes and the majority of whose passengers use the buses for traveling a distance not exceeding 40 miles, measured one way, on the same day between their place of abode and their place of work, shopping areas, or schools, is equipped with a tire that has a tread depth measuring less than 2/32 of an inch when measured as follows:

NOTE: The exemptions provided in (i) and (ii) of this paragraph subdivision 5 do not apply to buses owned or operated by any public school district, private school or contract operator of buses.

NOTE: Measure in two adjacent tread grooves where tread is thinnest. Refer to Figure 1. If either of the grooves measure 2/32 of an inch or more, no further measurements are necessary and tread depth is satisfactory. Do not take measurements from the tread wear indicators.

6. If both adjacent grooves measure less than 2/32 of an inch, the tire tread depth must be measured again at two additional equally spaced intervals around the circumference of the tire in a like manner as the first measurement. Refer to Figure 1. If the tread depth is less than 2/32 of an inch in two adjacent tread grooves at each of the equally spaced intervals, the tire must be rejected.

 

MEASURE WHERE THE TREAD IS THINNEST IN TWO ADJACENT TREAD GROOVES

 

 

 http://leg5.state.va.us/images/399193858547VSPRE_files/image001.gif
FIGURE 1

IF THE DEPTH IS LESS THAN 2/32-INCH IN BOTH GROOVES, MEASURE AT TWO ADDITIONAL EQUALLY SPACED INTERVALS

7. A tire equipped with tread wear indicators if found to have such indicators in contact with the pavement in any two adjacent grooves at three equally spaced intervals around the circumference of the tire. Refer to Figure 2.

 

 http://leg5.state.va.us/images/399193858547VSPRE_files/image002.gif
FIGURE 2

REJECT IF THE TREAD WEAR INDICATORS ARE IN CONTACT WITH THE PAVEMENT IN ANY TWO ADJACENT GROOVES AT THREE EQUALLY SPACED LOCATIONS

8. Any tire has a cut or puncture into the fabric. This does not include a plug or patch that may be used as a manner of repair.

NOTE: Plugs/patches Plugs or patches shall be in the tread area only. Plugs/patches Plugs or patches are not permitted in the sidewall of the tire.

9. Any tire is worn so that the fabric or steel cord is visible.

10. Any tire has knots or bulges in its sidewalls or if there is evidence of a broken belt under the tread, or if the tread is separating from the fabric. Any cracks in the sidewall where separation in the rubber is detected or the fabric is exposed, not to include fine hairline cracks.

11. Any tire that has been recut or regrooved except commercial tires so designed and constructed to provide for acceptable and safe recutting and regrooving. (Regrooved tires must be identified on each sidewall as a regrooved tire.)

12. Any wheel studs, bolts, nuts, lugs, or other fasteners (both spoke and disc wheels) are loose, broken, cracked, stripped, missing, damaged, or otherwise ineffective.

13. Wheels are installed on the vehicle in a reversed position, except the wheels on vehicles that are reversed to perform part of a dual wheel combination.

14. Directional tires and/or or wheels designed and manufactured to travel in one direction of rotation are not properly installed.

15. Rims or wheels are bent, cracked, or damaged so as to affect safe operation of the vehicle. Reject if lug nut holes are elongated (out of round).

NOTE: Refer to subdivision 1 of 19VAC30-70-180 (Clearance lamps and reflectors) for tires that exceed more than four inches from the body.

19VAC30-70-140

19VAC30-70-140. Headlamps; except motorcycles.

A. Inspect for and reject if:

1. Any motor vehicle is not equipped with at least two headlamps of an approved type. The headlamps must be marked with the headlamp manufacturer's name or trademark, and DOT. If the headlamp bulbs are replaceable, the headlamp lens must be marked with the headlamp light source type (bulb) for which it was designed and the bulb must match the lens code.

NOTE: If the headlamp system is stamped to accept halogen bulbs, then the replacement bulbs must be halogen as well. Retrofitting an HID or LED bulb to a halogen headlamp system does not conform to the standards set forth by the Federal Motor Vehicle Safety Standards (FMVSS) and shall be rejected.

If the entire headlamp assembly is changed from a halogen system to an LED system and does not require the manufacture's original wiring to be cut or compromised, then it shall be considered for inspection if it meets the requirements of subdivision A 2 of this section.

2. Headlights are not of the same approved type (Halogen, HID, LED, etc.) except for sealed beam headlamps. At least two headlamps are required, or the replacement headlamp system does not contain all properly marked DOT and SAE stamps certifying that it has met and complied with the standards set forth by the Federal Motor Vehicle Safety Standard (FMVSS) 108.

NOTE: Replacement headlamps stamped with a DOT or SAE approval shall be considered approved by the Superintendent of State Police and will not be required to be listed on the Virginia Motor Vehicle Approved Equipment List.

3. In any headlamp the lens is cracked, broken, discolored, or rotated away from the proper position, or the reflector is not clean and bright.

4. Moisture or water buildup in headlamp is such that it affects the aiming pattern.

5. Headlamps omit light other than white. Light tints of color may be acceptable if the headlamp and headlamp bulbs are marked as required.

6. Bulbs are not of an approved type and marked with all of the following: light source type, the manufacturer's name or trade mark, and DOT.

NOTE:

Approved headlamp bulbs: HB1, HB2, HB3, HB3A, HB4, HB4A, HB5, H1, H3, H7, H8, H8B, H9, H9B, H9C, H11, H11B, H11C, H13, H13C, H15, HIR1, HIR2, H18, H19.

Approved headlamp bulbs that require ballast: 9500, D1R, D1S, D2R, D2S, D3R, D3S, D4R, D4S, D5S, D7S, D8S, D9S.

Approved headlamp ballasts must be marked with the light source type (bulb) and DOT. The bulb type marked on the ballast must match the marking on the headlamp lens.

7. Any filament or bulb in headlamps fails to burn properly or headlamps are not at the same location or configuration as designed by manufacturer. (Location and type of headlamps can be found in subsection E of this section.)

8. Wiring is dangling or connections are loose;, or if proper filaments do not burn at different switch positions; or if switches, including foot or hand dimmer, do not function properly and are not convenient to the driver.

9. Foreign material is placed on or in front of the headlamp lens or interferes with the beam from the lamp. No glazing may be placed over or in front of the headlamps unless it is a part of an approved headlamp assembly.

a. Reject if vehicle has wire, unapproved lens or plastic covers, any other materials that are not original equipment or any colored material placed on or in front of the headlamps.

b. Vehicles registered as street rods may have clear, rigid plastic or glass headlamp lens covers in front of sealed beam units to replace original manufacturer's equipment.

EXCEPTION: A clean impact film known as Headlight Savers produced by Grand Prix Motoring Accessories may be applied to the headlight lens to absorb impact of rocks, etc.

10. Lamps can be moved easily by hand due to a broken fender or loose support, or if a good ground is not made by the mounting.

11. Headlamps, auxiliary driving lamps and front fog lamps are not mounted so that the beams are aimable and the mounting does not prevent the aim of the lighting device from being disturbed while the vehicle is operating on public roads. All lamps shall be securely mounted on a rigid part of the vehicle.

12. A headlamp visor is over two inches long unless part of the original body design.

13. The high beam indicator in the driver's compartment does not burn when the high beam is on or does not go off when the low beam is on. (Vehicles not originally equipped with an indicator are not required to comply unless sealed beam headlamps have been installed.)

B. Aiming the headlamps.

1. Headlamps Inspectors shall rely on their education, training, and experience to determine if the headlamps are properly aimed. If improper alignment is observed, headlamps shall be checked for proper aim by using an optical headlamp aimer on every motor vehicle inspected, except on vehicles equipped with on-board aimers.

Headlamp aim on vehicles with on-board aimers shall be checked by visually examining the leveling device mounted either on or adjacent to the headlamp. Reject the vehicle if the leveling device shows the headlamp adjustment to exceed indicated specifications.

NOTE: Driving lamp and fog lamps must be aimed using the optical aimer, according to instructions in 19VAC30-70-160 I 10 i and 11 g (2) visually inspected to ensure proper aiming. If improper alignment is observed, the optical aimer shall be used to correct any misalignment.

2. Headlamps are not aimed within the following tolerances using the optical aimer.

a. The center of the hot spot of all single element high beam lamps is set more than four inches up or down from the horizontal centerline or more than four inches to the left or right from the vertical centerline.

b. The left edge of the lamp pattern of any low beam lamp or any combination or multi-element lamp is more than four inches to the left or right of the vertical centerline or the top edge of the lamp pattern is more than four inches above or below the horizontal centerline when checked on low beam.

C. Optical aimer.

1. Approved optical headlamp machines shall be used to properly aim all headlamps, except vehicles with on-board aimers. Optical aimers must be properly calibrated and used in the manner recommended by the manufacturer.

The optical headlamp machine must be aligned to the vehicle in accordance with the manufacturer's specifications.

2. When aiming headlamps, first look for the type of lamp, which will be found embossed on the lens. The type determines which aiming requirements must be followed for the optical aimer.

3. All low beam or combination/multi-element headlamps must be set by aiming the lamp pattern with the lamps set on low beam.

NOTE: If attempting to align a composite or sealed beam lamp with a high and low beam within the same housing, align only the low beam. If aligning a four-lamp system with high and low beams in separate housings, it may be necessary to cover the low beam while aligning the high beam, if all four lamps are on at the same time.

4. Pattern should be aimed so that the left edge does not extend to the left or right of straight ahead, and the top of the pattern should be even with the horizontal.

Pattern "A" represents the light pattern as it should appear on the view screen of the approved aimer when checking the low-beam pattern on a single element headlamp or a combination multi-element headlamp.

 http://leg5.state.va.us/images/399194865070VSPRE_files/image001.gif

5. All VOL and VOR headlamps will be aimed as follows:

To properly aim a combination multi-element or low-beam VOL or VOR headlamp assembly, the headlamp pattern should be aimed on low beam only.

Letters marked on the headlamp cover should properly identify VOL and VOR headlamps.

NOTE: VOL and VOR headlamps will normally have only one adjustment, which will be for the vertical aim only. The horizontal aim should be disregarded, as the horizontal aim is preset at the factory.

6. All single element high beam headlamps shall be set by aiming the center of the hot spot with the lamps set on high beam.

7. Aim straight ahead-center of the hot spot should be centered with the vertical and horizontal centerlines.

Pattern "B" represents the light pattern as it should appear on the view screen of the approved aimers.

 http://leg5.state.va.us/images/399194865070VSPRE_files/image002.jpg

8. When lamp pairs are mounted horizontally, the low beam lamp must be on the outer side and when mounted vertically, the low beam lamp must be at the higher position in the pair.

9. The four headlamp system must be wired so that only the lower beam lamp will burn when the light beams are depressed. When switched to high beams, both high beam and low beam may burn.

The "F" type halogen headlamp 1986 (LF-UF) of the four headlamp system will function in the following manner: system must be used so the low beam does not burn with the high beam.

D. Headlamps on vehicles used for snow removal. Approved auxiliary headlamps may be mounted above the conventional headlamps. (These lamps must be in compliance with this section in its entirety, subdivision 7 of 19VAC30-70-150, and 19VAC30-70-170.)

E. Inspect for and reject if:

1. Lamps are not an approved type as previously indicated in section subdivision A 6 of this section.

2. Lamps are not mounted in a manner that will permit proper aiming.

3. Lamps are mounted so as to obstruct the driver's vision.

4. The auxiliary headlamp circuit does not contain a switch that will deactivate the primary headlamp system when the auxiliary headlamps are in use.

5. Auxiliary headlamps are not aimed in accordance with the provisions of subdivision B 2 of this section.

6. Headlamps are not wired in accordance with the provisions of subdivision C 8 of this section.

NOTE: Light patterns shown in the following diagram will be displayed on the most recently approved light machines produced by Hopkins and Symtech Corporations.

HEADLAMP PATTERNS

 

 http://leg5.state.va.us/images/399718294258VSPRE_files/image001.jpg

 http://leg5.state.va.us/images/399718294258VSPRE_files/image002.gif

 

 

 

 

NOTE: Always inspect the following sealed beam and replaceable bulb and integral beam headlamps on LOW BEAM only:

- 5-3/4 inch, marked 2, 2C, or 2C1

- 7 inch, marked 2, 2D, or 2D1

- 100 X 165mm rectangular, marked 2A, 2A1, or 2E1, 2G1 or 2H1

- 200 X 142mm rectangular, marked 2B or 2B1

- Replaceable bulb headlamp, marked LF with 9004 (HB1)

- 92 X 160mm rectangular, marked LF

- Replaceable bulb headlamps with 9006 (HB4) alone or in combination with 9005 (HB3)

- 55 X 135mm rectangular, marked L

- Integral beam headlamp when high and low beam reflectors move together.

19VAC30-70-150

19VAC30-70-150. Rear lamps: tail lamp; license plate lamps; and rear lamp combinations.

Inspect for and reject if:

1. Vehicle is not equipped with a rear (tail lamp) or rear lamp combination of an approved type or light assembly does not work as designed by the manufacturer. The approval designation letters that must appear are DOT or SAE-A-I-S-T-P for single lamps, DOT or SAE-A-I-S-T-P-R with a backup light, DOT or SAE-A-I-S-T-P-P2-R with a wrap around side-marker lamp and backup light.

2. The vehicle is equipped with more than one rear lamp, if all are not in operating condition.

3. The vehicle is not equipped with a license plate lamp of an approved type (DOT or SAE-L) that emits a white light. The license plate lamp may be a separate lamp or part of a combination rear lamp.

4. License plate is not illuminated by an approved a license plate lamp that emits a white light.

5. Lens on rear lamps, or lens area in combination rear lamps (tail lamps) are not red or contain a dot of another color. LED (light-emitting diode) lights with a clear lens are acceptable if of an approved type. For those vehicles that are Vehicles equipped with a multiple LED light lights (not filament-burning bulbs), they will pass a safety inspection if more than 50% of the diode lights are burning.

NOTE: Replacement tail lamps, commonly sold as "clear" tail lamps or "Euro-Tail" lamps will not pass inspection if the red lamps are replaced with clear ones.

6. Lens has piece broken from it or does not fit properly. The lens may have one or more cracks provided an off-color light does not project through the crack or cracks. Taping or gluing cracks or pieces is not permitted.

7. Filament in all rear (tail) lamps does not burn when headlamp switch is turned on to any position, or if lamps do not provide a red light visible to the rear through an approved red lens as annotated in subdivision 1 of this section. If it is a rear lamp combination incorporated with a wrap around wraparound side-marker light, then the side-marker lens must be red and not a clear lens with a red bulb. If the bulb, socket and wiring are removed from the side-marker lamps, then they will not be considered during the inspection.

8. Rear (tail) lamp is not mounted near extreme rear of vehicle. Dump trucks and other specially constructed vehicles may mount the rear lamp at a point other than on the extreme rear, provided such rear lamp is clearly visible from the rear, and further provided that a red reflector of an approved type is mounted on the extreme rear. In unusual cases, the rear lamp may be mounted on the cab. Reject if the lamp is hidden by a bolster or other part of the body or frame, is not mounted securely, or if the lamp does not make a good electrical contact.

9. The vehicle has wire, unapproved lens or plastic covers, any other materials that are not original equipment or any colored material placed on or in front of rear lamps, license plate lamps and rear lamp combinations.

10. Wiring or electrical connections are defective or filaments do not burn.

NOTE: Every trailer shall carry at the rear two red tail lights of a type approved by the superintendent.

19VAC30-70-160

19VAC30-70-160. Auxiliary lamps: backup; cornering; driving; fog; spot and warning.

A. Auxiliary lamps on a vehicle consist of seven general types: backup lamps (SAE-R), cornering lamps (SAE-K), driving lamps (SAE-Y), front fog lamps with an amber or clear lens (SAE-F) and rear fog lamps with red lens (SAE-F2), spot lamps (SAE-O), warning lamps (SAE-W, W2, W3), and daytime running lamps (DRLs) (SAE-Y2).

B. School buses may be equipped with an eight-lamp warning system of two red and two amber warning lamps of an approved type (SAE-W2) on the front and rear of such vehicle.

1. School buses may also be equipped with roof-mounted flashing white or amber warning lamps of an approved type (SAE-W2).

2. In addition to required warning lamps, school buses may be equipped with a stop signal arm consisting of an octagonal sign which meets FMVSS specifications (Federal Motor Vehicle Safety Standards, 49 CFR Part 571). The stop signal arm shall be reflectorized or be equipped with two red warning lamps of an approved type.

C. There is no limit on the number of backup lamps that a vehicle may have so long as they are of an approved type (SAE-R).

D. No more than four lamps, including two headlamps, may be lighted at any time to provide general illumination ahead of the vehicle.

E. Approved type (DOT or SAE-W) (SAE-W) blue or blue and red lights are permitted on Department of Corrections vehicles designated by the Director of the Department of Corrections and any law-enforcement vehicle.

1. Approved type secondary warning lights installed only on the four corners, on law-enforcement vehicles, Department of Corrections, fire apparatus, government-owned vehicle operated on official business by a local fire chief or other local fire official, rescue squad vehicle, ambulance, or any other emergency medical vehicles. These lights shall also have primary warning lights installed.

2. The hide-away or undercover strobe lights shall be installed in the side marker lights, tail lights or parking lights. The strobe itself must be clear and the lens color must continue to be the same type and color as originally approved. It will not be permissible to install the hide-away lights in the headlights.

3. Approved type (SAE-W) red warning lights or red and white lights showing to the front are permitted on fire department vehicles, including publicly-owned state forest warden vehicles, ambulances, any rescue vehicle used for emergency calls, local department of emergency management, animal warden vehicles, school buses and vehicles used by security personnel at the Newport News Shipbuilding and Drydock Company, Bassett-Walker, Incorporated, the Tultex Corporation, the Winchester Medical Center, or the National Aeronautics and Space Administration's Wallops Flight Facility.

4. No more than two flashing or steady-burning red lights or red and white combination lights of an approved type (SAE-W) may be installed on one vehicle owned by any member of a fire department, volunteer fire company or volunteer rescue squad, any ambulance driver employed by a privately-owned ambulance service, and any police chaplain.

F. Vehicles mentioned in subsection E of this section permitted to be equipped with flashing, blinking or alternating red, red and white, blue, or blue and red emergency lights (except vehicles owned by any member of a fire department, volunteer fire company, volunteer rescue squad or any ambulance driver employed by a privately-owned ambulance service) may be equipped with the means to flash their headlamps when their emergency warning lamps are activated provided:

1. The headlamps are wired to allow either the upper beam or lower beam to flash but not both.

2. The headlamp system includes a switch or device which prevents flashing of headlamps when headlamps are required to be lighted pursuant to current statute.

3. Emergency vehicles in Chesapeake, Poquoson, and York County may be equipped with flashing headlights that will function whenever their warning lights are activated.

G. Any firefighting vehicle, ambulance, rescue or life-saving vehicle, Virginia Department of Transportation vehicle, or tow truck may be equipped with clear auxiliary lamps which shall be used exclusively for lighting emergency scenes. Such lamps shall be of a type permitted by the superintendent. Any government-owned police vehicle may be equipped with clear auxiliary lamps of a type approved by the superintendent.

H. Approved type (SAE-W) amber flashing, blinking or alternating lights are permitted on vehicles used for the principal purpose of towing or servicing disabled vehicles or in constructing, maintaining and repairing highways or utilities on or along public highways and vehicles used for the principal purpose of removing hazardous or polluting substances from the state waters or drainage areas on or along public highways. Such lamps are permitted on vehicles used for servicing automatic teller machines, refuse collection vehicles, hi-rail vehicles and on vehicles used for towing or escorting over-dimensional materials, equipment, boats, or manufactured housing units by authority of highway hauling permit.

1. Approved type (SAE-W) amber flashing, blinking or alternating lights are permitted on fire apparatus, government-owned vehicles operated on official business by a local fire chief or other local fire official, rescue squad vehicles, ambulances, and any other emergency medical vehicles to be equipped with alternating blinking or flashing red, or red and white secondary lights mounted inside the vehicle's tail lights or marker lights.

2. Approved type (SAE-W) amber flashing, blinking or alternating lights are permitted on vehicles owned and used by municipal safety officers in the performance of their official duties, businesses providing security services and vehicles used to collect and deliver the United States mail, vehicles used by law-enforcement personnel in the enforcement of laws governing motor vehicle parking, government-owned law-enforcement vehicles provided the lights are used for giving directional warning, and vehicles used to provide escort for funeral processions.

3. Approved type (SAE-W) amber flashing, blinking or alternating lights are permitted on vehicles used as pace cars, security vehicles, or firefighting vehicles by any speedway or motor vehicle race track.

4. An approved type (SAE-W) amber flashing, blinking or alternating light may be mounted on the rear of any vehicle used to transport petroleum products. The light must be wired through the reverse gear circuit and activate in conjunction with the back-up lights and audible alarm.

5. An approved type (SAE-W) green warning light is permitted on vehicles used by police, firefighting, or rescue personnel as command centers at the scene of incidents. Such lights shall not be activated while the vehicle is operating upon the highway.

6. Approved type (DOT or SAE-W) (SAE-W) colored warning lights may be used by dealers or businesses engaged in the sale of fire, emergency medical services, or law-enforcement vehicles. They may, for demonstration purposes, equip such vehicles with colored warning lights.

I. Inspect for and reject if:

1. Auxiliary lamp is being used for a purpose other than for which it is manufactured or previously approved by the superintendent.

2. Auxiliary lamp does not have a clear lens.

3. Any reflector in such auxiliary lamp device is not clear.

EXCEPTIONS: An auxiliary lighting device that is both covered and unlit shall not be considered for inspection. An auxiliary lighting device that has a clear lens, has clear reflectors, and is unlit shall not be considered for inspection. Fog and driving lamps mounted below the level of the regular headlamps must be checked for aim as outlined in subdivisions I 12 h and 13 f of this section if not covered.

NOTE: The covers shall be a type that would be installed as original equipment and not tape, paper bags, aluminum foil or similar materials.

4. A vehicle has installed on it a warning lamp (DOT or SAE-W) (SAE-W) that is not of an approved type or has been altered.

Reject if the vehicle has wire, unapproved lens or plastic covers, any other materials that are not original equipment or any colored material placed on or in front of any auxiliary lamps: backup, cornering, driving, fog, spot, or warning lamps.

5. Motor vehicles may be equipped with more than two fog or auxiliary lights; however, only two of these types of lights can be illuminated at any time. Reject a vehicle equipped with a headlamp mounted or used as an auxiliary lamp.

6. Vehicle is equipped with an auxiliary lamp that does not function properly. (If an auxiliary lamp has been modified by removing the wiring, bulb and socket, the unit will be considered an ornament and not a lamp and will not be considered in inspection.)

7. Vehicle is equipped with a lighted advertising sign, except commercial motor vehicles, buses operated as public carriers, taxicabs, and privately-owned passenger cars used for home delivery of commercially prepared food. Commercial motor vehicles, buses operated as public carriers, and taxicabs may be equipped with vacant and destination signs and one steady burning white light for the nighttime illumination of external advertising. Privately-owned passenger cars used for home delivery of commercially prepared food may be equipped with one steady burning white light for the nighttime illumination of a sign identifying the business delivering the food. Do not reject approved identification lights.

8. Any lamp is not of an approved type or if lamps to be burned together as a pair do not emit the same color light.

9. The lens has a piece broken from it. The lens may have one or more cracks provided an off-color light does not project through the crack. Taping or gluing cracks or pieces is not permitted.

10. Backup lamps are not required. However, if installed they must operate and be inspected.

Inspect for and reject if:

a. Required lamps are not of an approved type (DOT or SAE-R) (SAE-R) or a lamp has been altered;

b. Wiring or electrical connections are defective or filaments do not burn;

c. The lens has a piece broken from it. The lens may have one or more cracks provided an off-color light does not project through the crack. Taping or gluing cracks or pieces is not permitted;

d. Lens is other than clear. LED (light-emitting diode) lights with a clear lens are acceptable if of an approved type. For those vehicles that are equipped with a multiple LED light (not filament-burning bulbs), they will pass inspection if more than 50% of the diode lights are burning;

e. Lamps are not wired into the reverse gear. Vehicles manufactured without backup lamps may be wired into an independent circuit.

11. Cornering lamps are not required. However, if installed they must operate and be inspected.

Inspect for and reject if:

a. Required lamps are not of an approved type (DOT or SAE-K) (SAE-K) or a lamp has been altered;

b. Wiring or electrical connections are defective or filaments do not burn;

c. The lens has a piece broken from it. The lens may have one or more cracks provided an off-color light does not project through the crack. Taping or gluing cracks or pieces is not permitted;

d. The color of the light is other than clear or amber;

e. The lamps do not burn in conjunction with the turn signals.

12. Driving lamps are not required. However, if installed they must operate and be inspected.

Inspect for and reject if:

a. Driving lamps are installed on vehicles equipped with the four-headlamp system, except the "F" type headlamp system;

b. Driving lamps are not of an approved type or have been altered;

c. The color of the lamp is other than white;

d. The lens has a piece broken from it or is rotated away from its proper position. The lens may have one or more cracks provided an off-color light does not project through the crack. Taping or gluing cracks or pieces is not permitted;

e. Wiring or electrical connections are defective;

f. Any driving lamp is mounted above the level of the regular headlamps, or is not mounted firmly to prevent excessive vibration;

g. Driving lamps are not wired so that they will burn only when the high beams of the regular headlamps are activated;

h.  Driving lamps are not aimed so that the center of the hot spot drops three inches in 25 feet so that the hot spot is directly ahead of the lamp.

NOTE: Driving lamps must be aimed using the optical headlight aimer. A tolerance of four inches in 25 feet is allowed in both the horizontal and the vertical adjustment.

13. Fog lamps are not required. However, if installed they must operate and be inspected.

Inspect for and reject if:

a. A vehicle may be equipped with more than two fog lamps; however, not more than two fog lamps can be illuminated at any time;

b. The lens is other than clear or amber. Fog lamps may have black-end bulbs or small metal caps over the end of the bulb;

c. The lens has a piece broken from it or is rotated away from its proper position. The lens may have one or more cracks provided an off-color light does not project through the crack. Taping or gluing cracks or pieces is not permitted;

d. Wiring or electrical connections are defective or filaments do not burn;

e. Any fog lamp is mounted above the level of the regular headlamps, or is not mounted firmly;

f. Lamps are not wired and aimed according to the following instructions:

(1) Fog lamps are general illumination lamps as covered in subsection A of this section. They must burn through the tail light circuit even if on a separate switch. If installed on a vehicle with a four-headlamp system, or a vehicle equipped with driving lamps, they must be wired into the low beam circuit.

(2) Fog lamps must be aimed so that the top edge of the high intensity zone is set at the horizontal centerline and the left edge of the high intensity zone is set at the vertical centerline. (Same as low beam headlights.)

NOTE: Fog lamps must be aimed using the optical headlight aimer. A tolerance of four inches in 25 feet is allowed in both the horizontal and the vertical adjustment.

14. Spot lamps are not required; however, if installed they must operate and be inspected.

Inspect for and reject if:

a. Vehicle is equipped with more than two spot lamps;

b. Lamps are not of an approved type (DOT or SAE-O) (SAE-O) or a lamp has been altered;

c. The lens in any spot lamp is other than clear;

d. The lens has a piece broken from it or is rotated away from its proper position. The lens may have one or more cracks provided an off-color light does not project through the crack. Taping or gluing cracks or pieces is not permitted;

e. Wiring or electrical connections are defective or filaments do not burn.

15. Daytime running lamps (DRLs) are not required. However, if installed they must operate and be inspected. DRLs must be installed in pairs.

NOTE: DRLs may or may not be wired into the tail light circuit.

Inspect for and reject if:

a. Any lamp, except headlamps, used as DRLs if not an approved type (SAE-Y2) and is not marked "DRL";

b. Fog lamps or parking lamps are used as DRLs;

c. More than one pair of lamps is used and designated as DRLs;

d. A DRL is mounted higher than 34 inches measured to the center of the lamp;

e. The color is other than white to amber;

f. DRLs do not deactivate when the headlamps are in any "on" position.

Any DRL optically combined with a turn signal or hazard lamp must deactivate when the turn signal or hazard lamp is activated and then reactivate when the turn signal or hazard lamp deactivates.

19VAC30-70-180

19VAC30-70-180. Clearance lamps, side marker lamps, and reflectors.

Inspect for and reject if:

1. Any motor vehicle, trailer, semitrailer or other vehicle is not equipped with clearance lamps if the vehicle is over seven feet wide or if any portion extends four inches or more outside the front fender line.

NOTE: See 19VAC30-70-550 for vehicles exceeding 10,000 GVWR.

When a motor vehicle with a trailer attached is presented, the combination may be considered as one unit in meeting this requirement. If presented separately, the individual unit must meet these requirements.

2. Lamps (DOT or SAE-P2, P3, PC, or PC2) or reflectors (DOT or SAE-A or B) are not of an approved type or a lamp has been altered; any wires are exposed; Reject if the vehicle has wire, unapproved lens lenses or plastic covers,; or any other materials that are not original equipment or any colored material placed on or in front of lamps or reflectors.

3. Lenses on or lamps on the front are not amber and lenses on lamps on the rear are not red or if a lens has a piece broken from it. A lens may have one or more cracks provided an off-color light does not project through the crack or cracks. Taping or gluing cracks or pieces is not permitted.

NOTE: LED (light-emitting diode) lights with a clear lens are acceptable if of an approved type. For those vehicles that are equipped with a multiple LED (light-emitting diode) light (not filament-burning bulbs),: they will pass inspection if more than 50% of the diode lights are burning.

4. Wiring or electrical connections are defective, all filaments do not burn.

5. Two amber lamps are not mounted on the front and two red lamps on the rear, so as to indicate the extreme width of the body, and as high on the permanent body as practical, except that approved 180 degree lamps with yellow or amber lens may be mounted on the side of the vehicle at or as near the front as possible, or if the front is not the widest portion, the lamps may be installed on the side and as near that point as possible. And with the further exception that 180 degree lamps with red lens may be mounted on the side of the vehicle at or as near the rear as possible or if the rear is not the widest portion of the vehicle, the lamps may be installed on the side as near that point as possible.

6. Any vehicle equipped with three red identification lamps with the lamp centers spaced not less than six inches or more than 12 inches apart and installed as close as practicable to the top of the vehicle and as close as practicable to the vertical centerline of the vehicle may have the rear clearance lamps required by subdivision 5 of this section, mounted at any height but indicate as nearly as practicable the extreme width of the vehicle.

NOTE: Other specially constructed vehicles may be equipped with the required clearance lamps not mounted on the extreme rear, provided such red lamps are clearly visible from the rear and provided further that two red reflectors of an approved type are mounted on the extreme rear. In unusual cases the rear lamp may be mounted on the cab and another red reflex reflector placed on the extreme rear.

NOTE: In addition to the required clearance lamps showing to the front and to the rear, a vehicle may be equipped with side marker lamps on the side of the vehicle. When such an installation is used, all of the clearance lamps on the side except the one at or near the rear must have an amber lens. The side marker lamps on the side at or near the rear must have a red lens.

7. Any vehicle covered by subdivision 1 of this section, except school buses, is not equipped with amber reflectors on the sides as near the front as practical, and red reflectors on the rear. The reflectors must be at least 15 inches and not more than 60 inches from the ground. No reflector can have a piece broken from its reflective surface, but may have one or more cracks. Taping or gluing cracks or pieces is not permitted.

8. Any combination of vehicles whose actual length exceeds 35 feet if the vehicles are not wide enough to require clearance lights, if the vehicle is not equipped with reflex reflectors of a type approved by the superintendent and mounted on the widest part of the towed vehicle so as to be visible from the front and sides of the vehicle. No reflector can have a piece broken from its reflective surface, but may have one or more cracks. Taping or gluing cracks or pieces is not permitted.

9. Any passenger vehicle is equipped with clearance lamps, unless such lamps are used to mark the extreme width of the vehicle or used as taxicab identification, or used as supplemental turn signals. (See 19VAC30-70-190 B.)

10. Vehicles so constructed as to make compliance with the requirements of subdivisions 1, 5, 7, 9, 11, and 12 of this section impractical will be equipped with clearance lamps and reflectors at the most practical location to provide maximum visibility.

11. Any vehicle is not equipped with two front side marker lights (amber) and two rear side marker lights (red).

12. Any vehicle is not equipped with two front side reflectors (amber), two rear side reflectors (red), and two reflectors mounted on the rear (red).

Description: Description: http://leg5.state.va.us/images/399198058174VSPRE_files/image001.gif

 




If equipped with three red identification lamps, the required clearance lamps may be mounted at any height so long as they indicate, as nearly as practicable, the extreme width of the vehicle.

Description: Description: http://leg5.state.va.us/images/399198058174VSPRE_files/image002.gif




NOTE: Must be equipped with three red identification lamps

 

ILLUSTRATIONS FOR PROPER INSTALLATION OF REFLECTORS

Description: Description: http://leg5.state.va.us/images/399198590455VSPRE_files/image001.gif





At least 15 inches and not more than 60 inches from the ground.

 

 

 

Amber Reflector

 

Description: Description: http://leg5.state.va.us/images/399198590455VSPRE_files/image002.gif




Red Reflectors: At least 15 inches and not more than 60 inches from the ground.

 

 

19VAC30-70-210

19VAC30-70-210. Glass and glazing.

A. Motor vehicles may be inspected without windshields, side glasses, or any kind of glazing, except that any motor vehicle other than a motorcycle that was manufactured, assembled, or reconstructed after July 1, 1970, must be equipped with a windshield. If glass or other glazing is installed, it must be inspected. If no windshield is installed, see 19VAC30-70-50 C for location of the sticker.

B. Inspect for and reject if:

1. Any motor vehicle manufactured or assembled after January 1, 1936, or any bus, taxicab or school bus manufactured or assembled after January 1, 1935, is not equipped throughout with safety glass, or other safety glazing material. (This requirement includes slide-in campers used on pickups or trucks, caps, or covers used on pickup trucks, motor homes, and vans.)

2. Any safety glass or glazing used in a motor vehicle is not of an approved type and properly identified (refer to approved equipment section). (Replacement safety glass installed in any part of a vehicle other than the windshield need not bear a trademark or name, provided the glass consists of two or more sheets of glass separated by a glazing material, and provided the glass is cut from a piece of approved safety glass, and provided the edge of the glass can be observed.)

NOTE: A number of 1998 and 1999 model year Ford Contour/Mystique, Econoline and Ranger vehicles were produced without the AS-1 windshield marking as required by FMVSS #205. Ford has certified that these vehicles' windshields meet all performance standards and will not be rejected.

3. Any glass at any location where glass is used is cracked or broken so that it is likely to cut or injure a person in the vehicle.

4. Windshield has any cloudiness more than three inches above the bottom, one inch inward from the outer borders, one inch down from the top, or one inch inward from the center strip. The bottom of the windshield shall be defined as the point where the top of the dash contacts the windshield.

5. Any distortion or obstruction that interferes with a driver's vision; any alteration that has been made to a vehicle that obstructs the driver's clear view through the windshield. This may include large objects hanging from the inside mirror or mounted to the windshield, cell phone mounts, GPS devices, CB radios or tachometers mounted on the dash or windshield, hood scoops, and other ornamentation on or in front of the hood that is not transparent.

a. Any hood scoop installed on any motor vehicle manufactured for the year 1990 or earlier model year cannot exceed 2-1/4 inches high at its highest point measured from the junction of the dashboard and the windshield.

b. Any hood scoop installed on any motor vehicle manufactured for the 1991 or subsequent model year cannot exceed 1-1/8 inches high at its highest point measured from the junction of the dashboard and the windshield.

NOTE: Vehicles up to 10,000 pounds (GVWR) submitted for inspection, with a navigational device, video event recording device, or a crash avoidance camera mounted on the interior of the windshield; when the entire device is outside the area swept by the windshield wipers or any location above the AS-1 line, shall be issued an approval sticker if no other violations are detected.

6. Windshield glass, on the driver's side, has any scratch more than 1/4 inch in width and six inches long within the area covered by the windshield wiper blade, excluding the three inches above the bottom of the windshield. A windshield wiper that remains parked within the driver's side windshield wiper area shall be rejected.

EXCEPTION: Do not reject safety grooves designed to clean wiper blades if the grooves do not extend upward from the bottom of the windshield more than six inches at the highest point.

7. There is a pit, chip, or star crack larger than 1-1/2 inches in diameter at any location in the windshield above the three-inch line at the bottom.

8. At any location in the windshield above the three-inch line at the bottom (as measured from the junction of the dash board and the windshield) there is more than one crack from the same point if at least one of the cracks is more than 1-1/2 inches in length. There is any crack that weakens the windshield so that one piece may be moved in relation to the other. (If there is more than one crack running from a star crack that extends above the three-inch line, the windshield shall be rejected.)

EXCEPTION: NOTE: Windshield repair is a viable option to windshield replacement. However, the primary focus of windshield repairs is to stop or reduce further damage from roadway adversities, vibrations, ambient temperature changes, and weather. Repairs to minor damage may be made so long as the windshield meets all of the standards set forth in this section.

A windshield that has been repaired will pass inspection unless:

a. It is likely to cut or injure a person.

b. There is any distortion that interferes with a driver's vision.

c. The windshield remains weakened so that one piece may be moved in relation to the other.

d. The integrity of the windshield has obviously been compromised by the damage or the repair.

9. Any sticker is on the windshield other than an official one required by law or permitted by the superintendent. Authorization is hereby granted for stickers or decals, to include those required by any county, town, or city, measuring not more than 2-1/2 inches in width and four inches in length to be placed in the blind spot behind the rear view mirror. The normal location for any required county, town, or city sticker is adjacent to the right side of the official inspection sticker when viewed from inside the vehicle. The top edge of the sticker is to be approximately four inches from the bottom of the windshield. The left side edge adjacent to the official inspection sticker shall not be more than 1/4 inch from the right edge of the official inspection sticker when viewed from inside the vehicle. Valid Commercial Vehicle Safety Alliance (CVSA) inspection decals or similar commercial vehicle inspection decal issued by local law enforcement may be placed at the bottom right corner of the windshield when viewed from inside the vehicle. The top edge of such decals are to be approximately four inches from the bottom of the windshield when viewed from inside the vehicle and are to be located outside the area swept by the windshield wipers.

Any sticker or decal required by the laws of any other state or the District of Columbia and displayed upon the windshield of a vehicle submitted for inspection in this state is permitted by the superintendent, provided the vehicle is currently registered in that jurisdiction, and the sticker is displayed in a manner designated by the issuing authority and has not expired. This includes vehicles with dual registration; (i.e., Virginia and the District of Columbia).

NOTE: Any Virginia registered vehicle displaying a valid sticker or decal required by a county, town, or city is permitted by the superintendent to remain in its current location through December 31, 2018, unless such location conflicts with the inspection sticker placement. This provision will afford localities time to enact changes to regulations governing required stickers or decals that may be impacted by the 2018 inspection sticker placement change.

NOTE: Toll transponder devices may be affixed to the inside center of the windshield at the roof line just above the rear view mirror. If space does not allow, then the transponder device may be affixed to the immediate right of the mirror at the roof line.

NOTE: A licensed motor vehicle dealer may apply one transponder sticker no larger than one inch by four inches and one barcode sticker no larger than three inches by four inches to the driver's side edge of a vehicle's windshield to be removed upon the sale or lease of the vehicle provided that it does not extend below the AS-1 line. In the absence of an AS-1 line the sticker cannot extend more than three inches downward from the top of the windshield.

NOTE: Any vehicle displaying an expired sticker or decal on its windshield at the time of inspection, excluding a rejection sticker, shall not be issued an approval sticker unless the owner or operator authorizes its removal. A rejection sticker will be issued versus an involuntary removal.

10. Sunshading material words, lettering, numbers or pictures on the windshield that extend below the AS-1 line or three inches downward from the top of the windshield in the absence of an AS-1 line. Sunshading is permitted on the windshield if authorized by the Virginia Department of Motor Vehicles and indicated on the vehicle registration.

NOTE: Vehicles with permitted sunshading on the windshield must have a cut-out to accommodate the direct application of an approval or rejection sticker to the windshield in the location indicated in 19VAC30-70-50 C of or 19VAC30-70-60 E.

NOTE: Vehicles with logos made into the glass at the factory meet federal standards and will pass state inspection.

11. Any sunscreening material is scratched, distorted, wrinkled or obscures or distorts clear vision through the glazing.

12. Front side windows have cloudiness above three inches from the bottom of the glass or other defects that affect the driver's vision or one or more cracks that permit one part of the glass to be moved in relation to another part. Wind silencers, breezes or other ventilator adaptors are not made of clear transparent material.

EXCEPTION: Colored or tinted ventvisors that do not exceed more than two inches from the forward door post into the driver's viewing area are permitted.

13. Glass in the left front door cannot be lowered so a hand signal can be given. (This does not apply to vehicles that were not designed or manufactured for the left front glass to be lowered, provided the vehicle is equipped with approved turn signals.) If either front door has the glass removed and material inserted in place of the glass that could obstruct the driver's vision.

EXCEPTION: Sunscreening material is permissible if the vehicle is equipped with a mirror on each side.

14. Any sticker or other obstruction is on either front side window, rear side windows, or rear windows. (The price label, fuel economy label and the buyer's guide required by federal statute and regulations to be affixed to new or used vehicles by the manufacturer shall normally be affixed to one of the rear side windows.) If a vehicle only has two door windows, the labels may be affixed to one of these windows. If a vehicle does not have any door or side windows the labels may be temporarily affixed to the right side of the windshield until the vehicle is sold to the first purchaser.

NOTE: A single sticker no larger than 20 square inches in area, if such sticker is totally contained within the lower five inches of the glass in the rear window if a vehicle has only one outside mirror, a single sticker or decal no larger than 10 square inches located in an area not more than three inches above the bottom and not more than eight inches from the rearmost edge of either front side window, is permissible and should not be rejected.

A single sticker issued by the Department of Transportation to identify a physically challenged driver, no larger than two inches by two inches, located not more than one inch to the rear of the front door post, or one inch to the rear of the front ventilator glass, if equipped with a ventilator glass and no higher than one inch from the bottom of the window opening, is permitted on the front driver's side window on a vehicle specially equipped for the physically challenged.

15. Rear window is clouded or distorted so that the driver does not have a view 200 feet to the rear.

EXCEPTIONS: The following are permissible if the vehicle is equipped with a mirror on each side:

a. There is attached to one rear window of such motor vehicle one optically grooved clear plastic right angle rear view lens, not exceeding 18 inches in diameter in the case of a circular lens or not exceeding 11 inches by 14 inches in the case of a rectangular lens, which enables the operator of the motor vehicle to view below the line of sight as viewed through the rear window.

b. There is affixed to the rear side windows, rear window, or windows of such motor vehicle any sticker or stickers, regardless of size.

c. There is affixed to the rear side windows, rear window, or windows of such motor vehicle a single layer of sunshading material.

d. Rear side windows, rear window, or windows is clouded or distorted.

19VAC30-70-260

19VAC30-70-260. Hood latch system; batteries.

A. "Hood" means any exterior movable body panel forward of the windshield that is used to cover an engine, luggage, storage or battery compartment.

B. Inspect for and reject if:

1. Each hood is not provided with a hood latch system that will securely hold the hood in its proper fully-closed position.

2. A latch release mechanism or its parts are broken, missing or badly adjusted so that the hood cannot be opened and closed properly.

NOTE: The hood latch release inside the passenger compartment is only for security and shall not be rejected under this section. If the hood latch cable can be accessed from either the inside or outside of the vehicle and opened by pliers or similar method, then it will pass.

3. Latching system on a vehicle equipped with a tilt cab is defective, broken, missing, or not properly adjusted so that the tilt cab is held securely when it is in its latched position.

C. Battery mounting and storage. Inspect for and reject if:

1. A battery is not securely attached to a fixed part of the motor vehicle or trailer. A battery is not protected by a removable cover or enclosure if the battery is installed in a location other than the engine compartment.

2. All brackets, hardware, bolts, and bushings used for securely mounting the battery to the vehicle are not present.

3. Removable covers or enclosures are not substantial and are not securely latched or fastened.

4. The battery compartment does not have openings to provide ample battery ventilation and drainage.

5. Whenever the cable to the starting motor passes through a metal compartment, the cable shall be protected against grounding by an acid and waterproof insulating bushing.

6. Whenever a battery and a fuel tank are both placed under the driver's seat, (i) the battery and fuel tank are not partitioned from each other or (ii) each compartment is not provided with an independent cover, ventilation, and drainage.

19VAC30-70-300

19VAC30-70-300. Muffler, exhaust system and trailer venting.

A. Flexible tubing may be used anywhere in the exhaust system.

B. Inspection of exhaust system does not concern noise level.

C. Inspect for and reject if:

1. There is any leakage of exhaust gases at any point in the system. Do not reject "built-in" drain holes in muffler or tailpipe.

2. A muffler or catalytic converter has been repaired in any manner. The exhaust pipe may be welded to the muffler or catalytic converter. Holes or cracks in the exhaust line have been repaired with a patch or caulking.

NOTE: If a vehicle is inspected that does not have a muffler, the inspector should explain to the customer that although the vehicle will pass inspection without a muffler, it is a violation of state law for the vehicle to be operated on the highway without it.

NOTE: Nissan has designed an exhaust repair for leak/noise leak or noise at the front tube for the 2002-03 Nissan Pathfinders. The repair may require the application of a specially designed caulk to the front tube of the exhaust system. Since Nissan has designed the repair for their vehicles and trained Nissan technicians would perform the repair, this would be acceptable and should not be rejected. This exception would not preclude the rejection of exhaust systems repaired in a manner that is not designed or approved by the manufacturer and not performed by trained persons.

3. Tailpipe opening is mashed or pinched.

4. Any components of the exhaust system are not properly secured. Brackets or hangers are loose, broken, or missing.

5. The exhaust system fails to discharge the exhaust to the rear or sides of the passenger and trunk compartment of passenger vehicles unless such design is consistent with the original vehicle manufacturer exhaust system.

6. The exhaust system fails to discharge the exhaust to the rear or sides of the passenger compartment that is designed for and normally used for the driver and passengers of a property-carrying vehicle.

D. Trailers and semitrailer venting. Inspection of trailers and semitrailers will include a visual inspection of the venting of cooking or heating appliances to the outside of the trailer or semitrailer to determine if the heating and cooking appliances are adequately vented to the outside to prevent the asphyxiation of occupants of any trailer or semitrailer by the operation of the heating or cooking appliances.

1. Reject the trailer or semitrailer if not equipped with a vent or venting system to the outside.

2. Reject the trailer or semitrailer if there is any complete or partial obstruction of the vent or venting system.

NOTE: Exhaust pipes must direct the fumes to exit from underneath of the vehicle to the sides or rear most area.

NOTE: Exhaust pipes must extend behind the cab or rear axle of pickup trucks or utility trucks.

19VAC30-70-360

19VAC30-70-360. Motorcycle lights: auxiliary, headlamp, rear, signal, warning.

A. Headlamps. Inspect for and reject if:

1. Motorcycle is not equipped with at least one motorcycle headlamp.

2. Any motorcycle headlamp is not of an approved type (SAE-M). A motorcycle may have one or more headlamps. In addition to the headlamp or headlamps, a motorcycle may be equipped with not more than two auxiliary headlamps of a type approved (SAE-C) by the superintendent and identified as "auxiliary front lamps."

3. Lens and reflector do not match except in sealed units, or if the lens is cracked, broken or rotated, or if the lens and reflector are not clean or bright.

4. Any motorcycle lights-headlamp, rear lamp, signal or warning lamp has any wire, unapproved lens or plastic covers, any other materials that are not original equipment or any colored material placed on or in front of lamp or lens.

5. Lamp is not focused or any filament or bulb fails to burn.

6. Lamp is not mounted securely or if switch does not operate properly.

7. The center of the hot spot is set more than four inches up or down from the horizontal centerline or more than four inches to the left or right from the vertical centerline. The Inspectors shall rely on their education, training, and experience to determine if the headlamp is properly aimed. If improper alignment is observed, the headlamp shall be checked for proper aim by using an optical headlamp aimer.

8. The high beam indicator does not burn when the high beam is on or does not go off when the low beam is on.

NOTE: Motorcycles may be equipped with means of modulating the high beam of their headlights between high and low beam at a rate of 200 to 280 flashes per minute, provided they are equipped with a switch or device that prevents flashing of headlights when headlights are required to be lighted.

NOTE: Inspection is to be performed with lamp on high beam.

NOTE: The use of strobe lights being placed inside the headlamps of police motorcycles is permitted. The strobe light system developed by Harley-Davidson for use in police motorcycle headlamps has been tested and does meet the current standard; therefore, strobe light systems of this type and similar types may be used in police motorcycle headlamp systems.

B. Aiming the headlamp. All headlamps that do not comply with subdivision A 7 of this section shall be aimed straight ahead. (Zero inches up or down and zero inches to the right or left.)

C. Rear lamp. Inspect for and reject if:

1. The motorcycle is not equipped with a rear lamp of approved type (SAE-T-S-P-A).

2. The lamp is not mounted near rear of vehicle, or is not mounted securely, or if lamp does not make a good electrical connection.

3. Lenses are not red to the rear and clear or amber to the front or any lens has a piece broken from it. The lens may have one or more cracks provided an off-color light does not project through the cracks.

NOTE: LED (light-emitting diode) lights with a clear lens are acceptable if of an approved type. For those vehicles that are motorcycles equipped with a multiple LED light (not filament-burning bulbs), they will pass inspection if more than 50% of the diode lights are burning.

4. Filaments in all lamps do not burn when headlamp switch is turned on to any position.

5. The rear license plate is not illuminated by an approved license plate bulb.

D. Signal device (intention to stop or turn).

1. Signal devices are not required on motorcycles; however, if installed, they must operate and be inspected.

2. Signal lamp lenses installed on the front of the motorcycle shall be amber and be located on each side of the vertical centerline of the motorcycle and as far apart as practicable and not closer than nine inches, measured from the optical centerline of the lamps, and to be located on the same level and not less than 20 inches above the ground level. The optical centerline of the lamp shall not be less than four inches from the retaining ring of the headlamp unit.

3. Signal lamps installed on the rear of the motorcycle shall be red or amber and shall be located on each side of the vertical centerline of the motorcycle as far apart as practicable but not closer than nine inches, measured from the optical centerline of the lens, and shall be located on the same level and not less than 20 inches above the ground level.

4. Inspect for and reject if:

a. Motorcycle, except an antique vehicle not originally equipped with a stop lamp, is not equipped with at least one stop lamp of an approved type that automatically exhibits a red or amber light to the rear when the brake control foot pedal or hand grip brake control device is activated. (On motorcycles manufactured prior to January 1, 1972, the activation of the front wheel brake control device is not required to activate the stop lamp.)

NOTE: Motorcycles may be equipped with a means of varying the brightness of the vehicle's brake light upon application of the vehicle's brakes.

b. The signal lamp is not of an approved type (SAE-D) or does not flash.

c. Lens in brake lamp or signal lamp has a piece broken from it. (Lens in brake lamp or signal lamp may have one or more cracks provided an off-color light does not project through the crack or cracks.)

d. Wiring or electrical connections are defective or any filaments do not burn.

e. Switch is not convenient to the driver and not of an approved type.

f. Signal devices are not installed as provided in subdivisions D 1, 2, and 3 of this section.

E. Warning lights. Inspect for and reject if:

1. Warning lamps are not of an approved type or have been altered.

2. Any lighted advertising sign is present.

F. Auxiliary lights. Inspect for and reject if:

1. Motorcycle or autocycles are equipped with any color other than red or amber standard bulb running lights or light-emitting diode (LED) pods or strips.

2. Auxiliary lights are not directed toward the ground.

3. Auxiliary lights are not designed for vehicular use.

4. Auxiliary lights project a beam of light greater than 25 candlepower per bulb.

5. Auxiliary lights display a blinking, flashing, oscillating, or rotating pattern.

6. Auxiliary lights are attached to the wheels.

NOTE: Such lighting is not subject to approval by the Superintendent of the State Police.

19VAC30-70-450

19VAC30-70-450. Brakes: emergency parking or holding; batteries.

A. Some vehicles are equipped with an actual emergency brake, while others have only a parking or holding brake. Some types may be actuated by a foot or hand lever, while others may incorporate a switch or valve to actuate the brake. Air and vacuum brake systems may employ spring activating parking brakes.

B. Inspect for and reject if:

1. Vehicle or combination of vehicles is not equipped with a parking, holding, or emergency brake in good working order of the type installed as original standard factory equipment for the vehicle on which it is installed.

2. The brake actuating mechanism does not fully release when the control is operated to the off position.

3. Any mechanical parts are missing, broken, badly worn, or are inoperative.

4. Cables are stretched, worn, or frayed or not operating freely.

5. Parking brake will not hold the vehicle stationary with the engine running at slightly accelerated speed with shift lever in drive position for automatic transmission or shift lever in low gear with clutch engaged for standard shift transmission.

6. On vehicles equipped with automatic transmissions, the vehicle will start in any gear other than (P) park or (N) neutral. If the gearshift indicator does not identify the park (P) and neutral (N) positions, then the vehicle shall be rejected.

7. On vehicles equipped with manual transmissions, the vehicle will start in any gear if the clutch is not depressed or disengaged.

NOTE: This will not apply to older vehicles, which were not originally equipped with a neutral-safety switch, clutch disengagement system or clutch pedal position sensor by the manufacturer.

8. Any nonmanufactured hole(s) hole in the spring brake housing section of a parking brake.

NOTE: All commercial motor vehicles manufactured after March 7, 1990, shall be equipped with a parking brake system adequate to hold the vehicle or combination under any condition of loading except agricultural commodity trailers, converter dollies, heavy haulers and pulpwood trailers.

C. Battery mounting and storage.

Inspect for and reject if:

1. A battery is not securely attached to a fixed part of the motor vehicle or trailer. A battery is not protected by a removable cover or enclosure if the battery is installed in a location other than the engine compartment.

2. All brackets, hardware, bolts, and bushings used for securely mounting the battery to the vehicle are not present.

3. Removable covers or enclosures are not substantial and are not securely latched or fastened.

4. The battery compartment does not have openings to provide ample battery ventilation and drainage.

5. Whenever the cable to the starting motor passes through a metal compartment, the cable is not protected against grounding by an acid and waterproof insulating bushing.

6. Whenever a battery and a fuel tank are both placed under the driver's seat, (i) the batter and fuel tank are not partitioned from each other or (ii) each compartment is not provided with an independent cover, ventilation, and drainage.

19VAC30-70-490

19VAC30-70-490. Frame, engine mounts, coupling devices and emergency chains.

Inspect for and reject if:

1. Frame of any bus, truck, tractor truck is cracked, loose, broken or sagging. Frame of any trailer or semi-trailer has any broken cracked, loose, or sagging top or bottom frame rails or frame is cracked or broken.

2. Engine, transmission or cab mounts, to include all hardware, bolts, and bushings used to connect the mount to the vehicle, frame, engine, or transmission are broken or missing. Any engine or transmission mount shall be rejected if it allows the power train to come in contact with the firewall or other body parts. Cab mounts should be rejected if they do not properly secure the body to the frame.

3. Trailer hitch or pintle hook is not securely attached. Reject if the pintle eye or trailer drawbar has any cracks or if any welding repairs have been made to the pintle eye.

4. Chains, cables, etc., used to attach a towed vehicle are not securely attached, or are broken, worn or abraded.

5. Fifth wheel does not lock in position or have a locking mechanism that is in proper working order.

NOTE: Reject if horizontal movement exceeds 1/2 inch between upper and lower fifth wheel halves.

6. Fifth wheel assembly system has any leak of fluid or air.

7. Fifth wheel has any broken, missing, or damaged parts; or is not securely attached to the frame. This includes fore and aft stops.

8. Trailer king pin is not secure, or is broken, or worn so as to prevent secure fit in fifth wheel. The upper coupler device is not securely attached.

9. Any cracks, breaks or damaged parts in the stress or load bearing areas of a coupling device.

10. Trailer is not equipped with emergency chain(s) chains or steel cable(s) cables.

NOTE: Fifth wheel assembly does not require emergency chain or steel cable. A fifth wheel is defined as a device that interfaces with and couples to the upper coupler assembly of a semitrailer. The upper coupler assembly is a structure consisting of an upper coupler plate, king pin and supporting framework which interfaces with and couples to a fifth wheel. Ball and socket connections also referred to as hitch and coupling connections are not fifth wheel assemblies and do require an emergency chain or steel cable.

11. Sliding trailer tandem or multi-axle assemblies do not lock in place or have worn, broken or missing parts.

12. Any play is detected in the drive shaft u-joints, CV joints, or center load bearing.

19VAC30-70-500

19VAC30-70-500. Tires, wheels, rims.

Inspect for and reject if:

1. Any tire is marked specifically for use other than on the highway, such as "For Farm Use Only," "For Off-Highway Use Only," any tire marked "Not for Steering Axle," "For Mobile Home Use Only," or "For Trailer Use Only."

EXCEPTION: "For Trailer Use Only" tires are allowed when used on trailers only.

2. A radial tire is mismatched on the same axle with a bias ply tire or a bias belted tire.

3. Bias ply or bias belted tires are used on the rear axle when radial ply tires are used on the front axle. Except:

a. On a two-axle vehicle equipped with truck tires with 20-inch rim diameter and larger. Bias or radial tires may be used on either axle if the vehicle has dual rear wheels or is equipped with wide-base single tires.

b. Either bias or radial tires may be used on the steering axle of vehicles with three or more axles.

4. Bias tires and radial tires are mixed in a tandem-drive axle combination on a vehicle equipped with truck tires with 20-inch rim diameter and larger.

5. Any tire on the front wheel of a bus, truck or any tractor truck has a tread groove pattern of less than 4/32 inch when measured at any point on a major tread groove.

6. Any bus has regrooved, recapped, or retreaded tires on the front wheels.

7. Any motor vehicle, trailer or semitrailer, except the dual wheels installed on motor vehicles having seats for more than seven passengers: (i) operated wholly within a municipality, or (ii) operated by urban and suburban bus lines, which are defined as bus lines operating over regularly scheduled routes and the majority of whose passengers use the buses for traveling a distance of not exceeding 40 miles, measured one way, on the same day between their place of abode and their place of work, shopping areas, or schools, is equipped with a tire that has a tread depth measuring less than 2/32 of an inch when measured as follows: NOTE: The exemptions provided in clauses (i) and (ii) of this paragraph subdivision do not apply to buses owned or operated by any public school district, private school, or contract operator of buses.

NOTE: Measure in two adjacent tread grooves where tread is thinnest. If either of the grooves measure 2/32 of an inch or more, no further measurements are necessary and tread depth is satisfactory. Do not measure on tread wear indicators.

If both adjacent grooves measure less than 2/32 of an inch, the tire tread depth must be measured again at two additional equally spaced intervals around the circumference of the tire in a like manner as the first measurement. If the tread depth is less than 2/32 of an inch in two adjacent tread grooves at each of the equally spaced intervals, the tire must be rejected.

NOTE: Refer to Figures 1, 2, 3, and 4 in this section for illustrations of how to measure tire tread.

 

MEASURE WHERE THE TREAD IS THINNEST IN TWO ADJACENT TREAD GROOVES

Description: Description: Description: http://leg5.state.va.us/images/399352679498VSPRE_files/image001.gif
FIGURE 1

IF THE DEPTH IS LESS THAN 2/32-INCH IN BOTH GROOVES MEASURE AT TWO ADDITIONAL EQUALLY SPACED INTERVALS

8. A tire equipped with tread wear indicators if found to have such indicators in contact with the pavement in any two adjacent grooves at three equally spaced intervals around the circumference of the tire. Refer to Figure 2.

 

REJECT IF THE TREAD WEAR INDICATORS ARE IN CONTACT WITH THE PAVEMENT IN ANY TWO ADJACENT GROOVES AT THREE EQUALLY SPACED LOCATIONS

Description: Description: Description: http://leg5.state.va.us/images/399352679498VSPRE_files/image002.gif
FIGURE 2

9. Any tire has a cut to the extent a ply or belt material is exposed or puncture, not to include a plug or patch that may be used as a manner of repair.

NOTE: Plugs/patches Plugs or patches shall be in the tread area only. Plugs/patches Plugs or patches are not permitted in the sidewall of the tire.

10. Any tire is worn so that the fabric or steel cord is visible.

11. Any tire has knots or bulges in its sidewalls or if there is evidence of a broken belt under the tread, or if the tread is separating from the fabric.

12. Any tire that has been recut or regrooved except commercial tires so designed and constructed to provide for acceptable and safe recutting and regrooving. Each tire that has been regrooved must be labeled with the word "Regroovable" molded on or into the tire on both sidewalls in raised or recessed letters.

13. Any tire is flat or has an audible air leak.

14. Any tire so mounted or inflated that it comes into contact with its mate or any parts of the vehicle.

15. Rims, or lock rings or wheels are bent, cracked or damaged so as to affect safe operation of the vehicle. Reject if lug nut holes are elongated (out of round).

16. Any wheel studs, bolts, nuts, lugs, or other fasteners (both spoke and disc wheels) are loose, broken, cracked, stripped, missing, or damaged or otherwise ineffective.

17. Any welded repair on aluminum wheel(s) wheels on a steering axle or any welded repair (other than disc to rim attachment) on steel drive wheel(s) wheels mounted on the steering axle.

18. Directional tires and/or or wheels, designed and manufactured to go in a certain direction of rotation not installed in the proper direction of rotation.

Description: Description: Description: http://leg5.state.va.us/images/399353222220VSPRE_files/image001.gif

Description: Description: Description: http://leg5.state.va.us/images/399353222220VSPRE_files/image002.gif

19VAC30-70-510

19VAC30-70-510. Headlamps.

A. Inspect for and reject if:

1. Any motor vehicle is not equipped with at least two headlamps of an approved type. The headlamps must be marked with the headlamp manufacturer's name or trademark, and DOT. If the headlamp bulbs are replaceable, the headlamp lens must be marked with the headlamp light source type (bulb) for which it was designed and the bulb must match the lens code.

NOTE: If the headlamp system is stamped to accept halogen bulbs, then the replacement bulbs must be halogen as well. Retrofitting an HID or LED bulb to a halogen headlamp system does not conform to the standards set forth by the Federal Motor Vehicle Safety Standards (FMVSS) and shall be rejected.

If the entire headlamp assembly is changed from a halogen system to an LED system and does not require the manufacture's original wiring to be cut or compromised, then it shall be considered for inspection if it meets the requirements of subdivision A 2 of this section.

2. Headlights are not of the same approved type (Halogen, HID, LED, etc.) except for sealed beam headlamps. At least two headlamps are required., or the replacement headlamp system does not contain all properly marked DOT and SAE stamps certifying that it has met and complied with the standards set forth by the Federal Motor Vehicle Safety Standard (FMVSS) 108.

NOTE: Replacement headlamps stamped with a DOT or SAE approval shall be considered approved by the Superintendent of State Police and will not be required to be listed on the Virginia Motor Vehicle Approved Equipment List.

3. In any headlamp the lens is cracked, broken, discolored, or rotated away from the proper position, or the reflector is not clean and bright.

4. Moisture or water buildup in headlamp is such that it affects the aiming pattern.

5. Headlamps omit light other than white. Light tints of color may be acceptable if the headlamp and headlamp bulbs are marked as required.

6. Bulbs are not of an approved type and marked with all of the following: light source type, the manufacturer's name or trade mark, and DOT.

a. Approved headlamp bulbs: HB1, HB2, HB3, HB3A, HB4, HB4A, HB5, H1, H3, H7, H8, H8B, H9, H9B, H9C, H11, H11B, H11C, H13, H13C, H15, HIR1, HIR2, H18, H19.

b. Approved headlamp bulbs that require ballast:  9500, D1R, D1S, D2R, D2S, D3R, D3S, D4R, D4S, D5S, D7S, D8S, D9S.

c. Approved headlamp ballasts must be marked with the light source type (bulb) and DOT. The bulb type marked on the ballast must match the marking on the headlamp lens.

7. Any filament or bulb in headlamps fails to burn properly or headlamps are not at the same location or configuration as designed by the manufacturer. (Location and type of headlamps can be found in subsection B of this section.)

8. Wiring is dangling or connections are loose, or if proper filaments do not burn at different switch positions, or if switches --, including foot or hand dimmer --, do not function properly, and are not convenient to the driver.

9. Foreign material is placed on or in front of the headlamp lens or interferes with the beam from the lamp. No glazing may be placed over or in front of the headlamps unless it is a part of an approved headlamp assembly. Reject if the vehicle has wire, unapproved plastic covers, any other materials that are not original equipment or any colored material placed on or in front of the headlamps.

EXCEPTION: A clear impact film known as Headlight Savers produced by Grand Prix Motoring Accessories may be applied to the headlight lens to absorb impact of rocks, etc.

EXCEPTION: A law-enforcement special weapons and tactics (SWAT) or tactical armored vehicle, designed and manufactured exclusively for missions, may apply protective bars in front of the headlamps when designed and installed by the manufacturer.

NOTE: Headlamps, auxiliary driving lamps and front fog lamps shall be mounted so that the beams are aimable and the mounting shall prevent the aim of the lighting device from being disturbed while the vehicle is operating on public roads. All lamps shall be securely mounted on a rigid part of the vehicle.

10. Lamps can be moved easily by hand due to a broken fender or loose support, or if a good ground is not made by the mounting.

Headlamps, auxiliary driving lamps and front fog lamps shall be mounted so that the beams are aimable and the mounting shall prevent the aim of the lighting device from being disturbed while the vehicle is operating on public roads. All lamps shall be securely mounted on a rigid part of the vehicle.

11. A headlamp visor is over two inches long unless part of the original body design.

12. The beam indicator in the driver's compartment does not burn when the high beam is on. (Vehicles not originally equipped with an indicator are not required to comply unless sealed beam headlamps have been installed.)

13. Headlamps are not aimed within the following tolerances using optical aimer:

a. The center of the hot spot of all Type 1 lamps, all single element high beam lamps, and all lamps that do not have Type 2 embossed in the lens, is set more than four inches up or down from the horizontal centerline or more than four inches to the left or right from the vertical centerline.

b. The left edge of the lamp pattern of any low beam lamp or any combination or multi-element lamp or Type 2 lamp is more than four inches to the left or right of the vertical centerline or the top edge of the lamp pattern is more than four inches above or below the horizontal centerline.

Aiming the Headlamps:

NOTE: Headlamps shall be checked for proper aim by using an optical headlamp aimer on every motor vehicle inspected.

Inspectors shall rely on their education, training, and experience to determine if the headlamps are properly aimed. If improper alignment is observed, headlamps shall be checked for proper aim by using an optical headlamp aimer except on vehicles equipped with on-board aimers.

Headlamp aim on vehicles with on-board aimers shall be checked by visually examining the leveling device mounted either on or adjacent to the headlamp. Reject the vehicle if the leveling device shows the headlamp adjustment to exceed indicated specifications.

NOTE: Driving lamps and fog lamps must be visually inspected to ensure proper aiming. If improper alignment is observed, the optical aimer shall be used to correct any misalignment.

Optical Aimer:

NOTE: Approved optical headlamp machines may be used to properly aim any of the headlamps. Optical aimers must be properly calibrated and used in the manner recommended by the manufacturer.

NOTE: When aiming headlamps, first look for the type of lamp, which will be found embossed on the lens. The type determines which aiming requirements must be followed for the optical aimer.

NOTE: All Type 2 headlamps and all low beam or multi-element headlamps must be set by aiming the lamp pattern with the lamps set on low beam.

NOTE: If attempting to align a composite or sealed beam lamp with a high and low beam within the same housing, align only the low beam. If aligning a four-lamp system with high and low beams in separate housings, it may be necessary to cover the low beam while aligning the high beam, if all four lamps are on at the same time.

NOTE: Pattern should be aimed so that the left edge does not extend to the left or right of straight ahead, and the top of the pattern should be even with the horizontal.

NOTE: All VOL and VOR headlamps will be aimed as follows:

To properly aim a combination multi-element or low beam VOL or VOR headlamp assembly, the headlamp pattern should be aimed on low beam only.

Letters marked on the headlamp cover should properly identify VOL and VOR headlamps.

NOTE: VOL and VOR headlamps will normally have only one adjustment, which will be for the vertical aim only. The horizontal aim should be disregarded, as the horizontal aim is preset at the factory.

Pattern "A" represents the light pattern, as it should appear on the view screen of the approved aimer when checking the low beam pattern on a single element headlamp or a combination multi-element headlamp.

Description: Description: Description: http://leg5.state.va.us/images/399353523999VSPRE_files/image001.jpg

NOTE: All Type 1 headlamps and all headlamps that do not have Type 2 embossed in the lens shall be set by aiming the center of the hot spot with the lamps set on high beam.

NOTE: Aim straight ahead-center of the hot spot should be centered with the vertical and horizontal centerlines.

Pattern "B" represents the light pattern as it should appear on the view screen of the approved aimer.

Description: Description: Description: http://leg5.state.va.us/images/399353523999VSPRE_files/image002.jpg

NOTE: The four headlamp system combines four 5-3/4-inch lamps in pairs.

NOTE: One lamp embossed at the top as Type "1" and one embossed on the top as a Type "2" are arranged as a pair on each side.

NOTE: When lamp pairs are mounted horizontally, the Type "2" lamp must be on the outer side.

NOTE: The four headlamp system must be wired so that only the lower beam in the Type "2" lamps will burn when the light beams are depressed. When switched to high beams, both the Type "1" and Type "2" will burn.

NOTE: Light patterns shown on the following page will be displayed on the most recently approved light machines produced by Hopkins and Symtech Corporations.

Aiming the Headlamps:

NOTE: All headlamps that are found not to be within the four-inch tolerance shall be adjusted to zero inches up or down and zero inches to the right or left.

Headlamps on Vehicles used for Snow Removal:

NOTE: Approved auxiliary headlamps (SAE-Z) may be mounted above the conventional headlamps. (These lamps must be in compliance with 19VAC30-70-140, in its entirety, subdivision 7 of 19VAC30-70-150, and subsection A of 19VAC30-70-170 of this manual.)

B. Inspect for and reject if:

1. Lamps are not an approved type as indicated in subdivision A 6 of this section.

2. Lamps are not mounted in a manner that will permit proper aiming.

3. Lamps are mounted so as to obstruct the driver's vision.

4. The auxiliary headlamp circuit does not contain a switch that will deactivate the primary headlamp system when the auxiliary headlamps are in use.

5. Auxiliary headlamps are not aimed in accordance with the provisions of this section.

HEADLAMP PATTERNS

Description: Description: Description: http://leg5.state.va.us/images/399355553069VSPRE_files/image001.jpg

 

Description: Description: Description: http://leg5.state.va.us/images/399355553069VSPRE_files/image002.gif

NOTE: ALWAYS inspect the following sealed beam and replacement bulb headlamps on LOW BEAM only:

5-3/4 inch, marked Type 2 or 2CI

b. 7 inch, marked Type 2 or 2DI

- 6-1/2 X 4-1/4 inch rectangular, marked Type 2QA or 2A1

- 2000 X 142mm rectangular, marked Type 2B or 2B1

19VAC30-70-520

19VAC30-70-520. Rear lamps: tail lamp; license plate lamps; and rear lamp combinations.

A. Inspect for and reject if:

1. Vehicle is not equipped with a rear (tail lamp) or rear lamp combination of an approved type and the light or light assembly does not work as approved. The approval designation letters that must appear are DOT or SAE-A-I-S-T-P for single lamps and DOT or SAE-A-I-S-T-P-R if a backup light is incorporated.

2. The vehicle is equipped with more than one rear lamp, if all are not in operating condition.

3. The vehicle is not equipped with a license plate lamp of an approved type (DOT or SAE-L) which that emits a white light. The license plate lamp may be a separate lamp or part of a combination rear lamp. (A road tractor or tractor-truck that does not have a rear license plate is not required to have a license plate lamp.)

4. Lens for license plate lamp is not illuminated by an approved a license plate lamp that emits a white light.

5. Lens on rear lamps, or lens area in combination rear lamps (tail lamps) are not red or contain a DOT of another color. LED (light-emitting diode) lights with a clear lens are acceptable, if of an approved type. For those vehicles that are. Vehicles equipped with a multiple LED light (not filament-burning bulbs), they will pass inspection if more than 50% of the diode lights are burning.

6. Lens has piece broken from it or does not fit properly. The lens may have one or more cracks provided an off-color light does not project through the crack(s) cracks.

NOTE: Taping or gluing cracks or pieces is not allowed.

7. Filament in all rear (tail) lamps does not burn when headlamp switch is turned on to any position, or if lamps do not provide a red light visible to the rear through an approved red lens as annotated in subdivision 1 of this subsection.

8. Rear (tail) lamp is not mounted near extreme rear of vehicle. Dump trucks and other specially constructed vehicles may mount the rear lamp at a point other than on the extreme rear, provided such rear lamp is clearly visible from the rear, and further provided that a red reflector of an approved type is mounted on the extreme rear. In unusual cases, the rear lamp may be mounted on the cab. Reject if the lamp is hidden by a bolster or other part of the body or frame, is not mounted securely, or if the lamp does not make a good electrical contact.

9. Wiring or electrical connections are defective or filaments do not burn.

10. Any vehicle has unapproved lens or plastic covers, any other materials that are not original equipment or any colored material placed on or in front of rear lamps, tail lamps, license plate lamps or rear lamp combinations.

B. Every trailer shall carry at the rear, two red lights of a type approved by the superintendent.

19VAC30-70-530

19VAC30-70-530. Auxiliary lamps: backup; cornering; driving; fog; spot and warning.

A. Auxiliary lamps on a vehicle consist of seven general types: backup lamps (SAE-R), cornering lamps (SAE-K), driving lamps (SAE-Y), front fog lamps with an amber or clear lens (SAE-F) and rear fog lamps with red lens (SAE-F2), spot lamps (SAE-O), warning lamps (SAE-W), and daytime running lamps (DRLs) (SAE-Y2).

1. School buses may be equipped with an eight-lamp warning system of two red and two amber warning lamps of an approved type (SAE-W2) on the front and rear of such vehicle.

a. In addition to required warning lamps, school buses may be equipped with a stop signal arm consisting of an octagonal sign that meets FMVSS specifications (Federal Motor Vehicle Safety Standards, 49 CFR Part 571). The stop signal arm shall be reflectorized or be equipped with two red warning lamps of an approved type.

b. School buses may also be equipped with roof mounted flashing white or amber warning lamps of an approved type (SAE-W2).

2. Reject if the vehicle has wire, unapproved plastic covers, any other materials that are not original equipment or any colored material placed on or in front of any auxiliary lamps, backup, cornering, driving, fog, spot or warning lamps.

EXCEPTION: Any lighting device that is both covered and not illuminated, other than lamps required or permitted by this manual, shall not be considered for inspection. Fog and driving lamps mounted below the level of the regular headlights must be checked for aim as outlined in subdivisions K 10 i and K 11 g of this section, if not covered.

NOTE: The covers shall be a type that would be installed as original equipment and not tape, paper bags, aluminum foil or similar materials.

B. There is no limit on the number of backup lamps that a vehicle may have so long as they are of an approved type (SAE-R).

C. No more than four lamps, including two headlamps may be lighted at any time to provide general illumination ahead of the vehicle.

D. Approved type (DOT or SAE-W) (SAE-W) blue or blue and red lights are permitted on Department of Corrections vehicles designated by the Director of the Department of Corrections and any law-enforcement vehicle.

E. Approved type blue or blue and red lights as well as approved type hide-away or undercover strobe warning lights are permissible for use on Department of Corrections and any law-enforcement vehicles.

1. Approved type secondary warning lights installed only on the four corners, on Department of Corrections and any law-enforcement vehicles, fire apparatus, government-owned vehicle operated on official business by a local fire chief or other local fire official, rescue squad vehicle, ambulance, or any other emergency medical vehicles. These lights shall also have primary warning lights installed.

2. The hide-away or undercover strobe lights shall be installed in the side marker lights, tail lights or parking lights. The strobe itself must be clear and the lens color must continue to be the same type and color as originally approved. It will not be permissible to install the hide-away lights in the headlights or in the backup lights.

F. Approved type (SAE-W) red warning lights or red and white lights showing to the front are permitted on fire department vehicles, including publicly owned state forest warden vehicles, ambulances, any rescue vehicle used for emergency calls, local Departments of Emergency Management, animal warden vehicles, school buses and vehicles used by security personnel at the Newport News Shipbuilding and Drydock Company, Bassett-Walker, Incorporated, the Tultex Corporation, the Winchester Medical Center, or the National Aeronautics and Space Administration's Wallops Flight Facility.

G. No more than two flashing or steady-burning red or combination red and white lights of an approved type may be installed on one vehicle owned by any member of a fire company, volunteer fire company, volunteer rescue squad or any ambulance driver employed by a privately owned ambulance service.

H. Vehicles mentioned in subsections D, E and F of this section permitted to be equipped with flashing, blinking or alternating red, red and white, blue, or blue and red emergency lights (except vehicles owned by any member of a fire company, volunteer fire company, volunteer rescue squad or an ambulance driver employed by a privately owned ambulance service) may be equipped with the means to flash their headlamps when their emergency warning lamps are activated provided:

1. The headlamps are wired to allow either the upper beam or lower beam to flash but not both and;

2. The headlamp system includes a sensor that prevents flashing of headlamps when headlamps are required to be lighted pursuant to current statute.

Emergency vehicles in Chesapeake, Poquoson, and York County may be equipped with flashing headlights that will function whenever their warning lights are activated.

I. Any fire vehicle used exclusively for firefighting, any ambulance or rescue or lifesaving vehicle used for the principal purpose of emergency relief or any wrecker used for the principal purpose of towing disabled vehicles may be equipped with clear auxiliary lamps that shall be used exclusively for lighting emergency scenes. Such lamps shall be of a type permitted by the superintendent. Any government-owned police vehicle may be equipped with clear auxiliary lamps of a type approved by the superintendent.

J. Approved type (SAE-W) amber flashing, blinking or alternating lights are permitted on vehicles used for the principal purpose of towing or servicing disabled vehicles or in constructing, maintaining and repairing highways or utilities on or along public highways and vehicles used for the principal purpose of removing hazardous or polluting substances from the state waters or drainage areas on or along public highways. Such lamps are permitted on vehicles used for servicing automatic teller machines, refuse collection vehicles, hi-rail vehicles and on vehicles used for towing or escorting over-dimensional materials, equipment, boats, or manufactured housing units by authority of highway hauling permit.

1. Approved type (DOT or SAE-W) (SAE-W) amber, red, and red and white flashing, blinking or alternating warning lights are permitted on fire apparatus, ambulances, and rescue and life-saving vehicles, provided the lights are mounted or installed as to be visible from behind the vehicle.

2. Approved type (DOT or SAE-W) (SAE-W) amber flashing, blinking or alternating lights are permitted on vehicles owned and used by municipal safety officers in the performance of their official duties, by businesses providing security services and vehicles used to collect and deliver the United States mail, vehicles used by law-enforcement personnel in the enforcement of laws governing motor vehicle parking, and government-owned law-enforcement vehicles provided the lights are used for giving directional warning and vehicles used to provide escort for funeral processions.

3. An approved type amber flashing, blinking or alternating lights are permitted on vehicles used as pace cars, security vehicles, or firefighting vehicles by any speedway or motor vehicle race track.

4. An approved type (DOT or SAE-W) (SAE-W) amber flashing, blinking or alternating light may be mounted on the rear of any vehicle used to transport petroleum products. The light must be wired through the reverse gear circuit and activate in conjunction with the backup lights and audible alarm.

5. An approved type (SAE-W) green warning light is permitted on vehicles used by police, firefighting, or rescue personnel as command centers at the scene of incidents. Such lights shall not be activated while the vehicle is operating upon the highway.

K. Inspect for and reject if:

1. Vehicle has an auxiliary lamp being used for a purpose other than that for which it was approved.

Do not reject tractor trucks equipped with cargo lights of an approved type (SAE-G) that are mounted on the rear of the tractor cab and wired through an independent switch used to illuminate brake connectors and fifth-wheels for nighttime hookups.

2. A vehicle has installed on it a warning lamp that is not of an approved type or has been altered.

3. Vehicle is equipped with a combination of auxiliary lamps which include more than two fog lamps, or more than two spot lamps, or more than two driving lamps. Motor vehicles may be equipped with more than two fog or auxiliary lights; however, only two of these types of lights can be illuminated at any time. Reject a vehicle equipped with a headlamp mounted or used as an auxiliary lamp.

NOTE: Vehicles equipped from the factory, with two driving lamps should not be rejected.

4. Vehicle is equipped with an auxiliary lamp that does not function properly. (If an auxiliary lamp has been modified by removing the wiring, bulb and socket, the unit will be considered an ornament and not a lamp and will not be considered for inspection.)

5. Vehicle is equipped with a lighted advertising sign, except commercial motor vehicles and buses operated as public carriers. These vehicles may be equipped with vacant and destination signs and one steadily burning white light for illumination of external advertising. Do not reject approved identification lights.

6. Any lamp is not of an approved type or if lamps to be burned together as a pair do not emit the same color light.

7. The lens has a piece broken from it. The lens may have one or more cracks provided an off-color light does not project through the crack or cracks.

8. Backup lamps are not required on motor vehicles less than 26,001 pounds GVWR. However, if installed they must operate and be inspected.

Inspect for and reject if:

a. Lamps are not of an approved type (DOT or SAE-R) (SAE-R) or a lamp has been altered.

b. Wiring or electrical connections are defective or filaments do not burn.

c. The lens has a piece broken from it. The lens may have one or more cracks provided an off-color light does not project through the crack or cracks.

d. Lens is other than clear. LED (light-emitting diode) lights with a clear lens are acceptable, if of an approved type. For those vehicles that are equipped with a multiple LED light (not filament-burning bulbs), they will pass inspection if more than 50% of the diode lights are burning.

e. Lamps are not wired into the reverse gear. Vehicles manufactured without backup lamps may be wired into an independent circuit.

9. Cornering lamps are not required. However, if installed they must operate and be inspected.

Inspect for and reject if:

a. Lamps are not of an approved type (DOT or SAE-K) (SAE-K) or a lamp has been altered.

b. Wiring or electrical connections are defective or filaments do not burn.

c. The lens has a piece broken from it. The lens may have one or more cracks provided an off-color light does not project through the crack or cracks.

d. The color of the light is other than clear or amber.

e. The lamps do not burn in conjunction with the turn signals.

10. Driving lamps are not required. However, if installed they must operate and be inspected.

Inspect for and reject if:

a. Driving lamps are installed on vehicles equipped with the four-headlamp system, except the "F" type headlamp system.

b. A vehicle is equipped with more than two driving lamps.

c. Driving lamps are not of an approved type (DOT or SAE-Y) (SAE-Y) or have been altered.

d. The color of the lamp is other than white.

e. The lens has a piece broken from it or is rotated away from its proper position. The lens may have one or more cracks provided an off-color light does not project through the crack or cracks.

f. Wiring or electrical connections are defective or filaments do not burn.

g. Any driving lamp is mounted above the level of the regular headlamps, or is not mounted firmly to prevent excessive vibration.

h. Driving lamps are not wired so that they will burn only when the high beams of the regular headlamps are activated.

i. Driving lamps are not aimed so that the center of the hot spot drops three inches in 25 feet so that the hot spot is directly ahead of the lamp.

NOTE: Driving lamps must be aimed using the optical headlight aimer. A tolerance of four inches in 25 feet is allowed in both the horizontal and the vertical adjustment.

11. Fog lamps are not required. However, if installed they must operate and be inspected.

Inspect for and reject if:

a. A vehicle may be equipped with more than two fog lamps; however, not more than two lamps can be illuminated at any time.

b. Lamps are not of an approved type (SAE or DOT-F or F2) or a lamp has been altered.

c. The lens is other than clear or amber. (Fog lamps may have black end bulbs or small metal caps over the end of the bulb.)

d. The lens has a piece broken from it or is rotated away from its proper position. The lens may have one or more cracks provided an off-color light does not project through the crack or cracks.

e. Wiring or electrical connections are defective or filaments do not burn.

f. Any fog lamp is mounted above the level of the regular headlamps, or is not mounted firmly.

g. Lamps are not wired and aimed according to the following instructions:

(1) Fog lamps are general illumination lamps as covered in 19VAC30-70-160 D. They must burn through the tail light circuit even if on a separate switch. If installed on a vehicle with a four-headlamp system or a vehicle equipped with driving lamps, they must be wired into the low beam circuit.

(2) Fog lamps must be aimed so that the top edge of the high intensity zone is set at the horizontal centerline and the left edge of the high intensity zone is set at the vertical centerline. (Same as low beam headlights.)

NOTE: Fog lamps must be aimed using the optical headlight aimer.

(3) A tolerance of four inches in 25 feet is allowed in both the horizontal and the vertical adjustment.

12. Spot lamps are not required. However, if installed they must operate and be inspected.

Inspect for and reject if:

a. Vehicle is equipped with more than two spot lamps.

b. Lamps are not of an approved type (DOT or SAE-O) (SAE-O) or a lamp has been altered.

c. The lens in any spot lamp is other than clear.

d. The lens has a piece broken from it or is rotated away from its proper position. The lens may have one or more cracks provided an off-color light does not project through the crack or cracks.

e. Wiring or electrical connections are defective or filaments do not burn.

13. Daytime running lamps (DRLs) are not required. However, if installed they must operate and be inspected. DRLs must be installed in pairs.

NOTE: DRLs may or may not be wired into the tail light circuit.

Inspect for and reject if:

a. Any lamp, except headlamps, used as DRLs is not an approved type (SAE-Y2) and is not marked "DRL."

b. Fog lamps or parking lamps are used as DRLs.

c. More than one pair of lamps are used and or designated as DRLs.

d. A DRL is mounted higher than 34 inches measured to the center of the lamp.

e. The color is other than white or amber.

f. DRLs do not deactivate when the headlamps are in any "on" position.

Any DRL optically combined with a turn signal or hazard lamp must deactivate when the turn signal or hazard lamp is activated and then reactivate when the turn signal or hazard lamp deactivates.

19VAC30-70-550

19VAC30-70-550. Clearance lamps, side marker lamps, and reflectors (under 26,000 pounds GVWR).

Inspect for and reject if:

1. Any motor vehicle, trailer, semitrailer or other vehicle is not equipped with clearance lamps if the vehicle is over seven feet wide or if any portion extends four inches or more outside the front fender line.

When a motor vehicle with a trailer attached is presented, the combination may be considered as one unit in meeting this requirement. If presented separately, the individual unit must meet these requirements except that any tractor-truck need not be equipped with rear red dimension or marker lamps.

2. Lamps (DOT or SAE-P2, P3, PC or PC2) or reflectors (DOT or SAE-A or B) are not of an approved type or a lamp has been altered; any wires are exposed; Reject if the lamps or reflectors have unapproved lenses or plastic covers,; or any other materials that are not original equipment or any colored material placed on or in front of lamps or reflectors.

EXCEPTION: A law-enforcement special weapons and tactics (SWAT) or tactical armored vehicle, designed and manufactured exclusively for SWAT missions, may apply protective bars in front of the clearance lamps, side marker lamps, and reflectors when designed and installed by the manufacturer.

Retro-reflective surfaces. Retro-reflective surfaces other than required reflectors may be used, provided (see diagram):

a. Designs do not resemble traffic control signs, lights, or devices, except that straight edge striping resembling a barricade pattern may be used.

b. Designs do not tend to distort the length and/or or width of the motor vehicle.

c. Such surfaces shall be at least three inches from any required lamp or reflector unless of the same color as such lamp or reflector.

d. No red color shall be used on the front of any motor vehicle, except for display of markings or placards required by law.

3. Lenses on or lamps on the front are not amber and lenses on lamps on the rear are not red or if a lens has a piece broken from it. A lens may have one or more cracks provided an off-color light does not project through the crack or cracks.

4. Wiring or electrical connections are defective or all filaments do not burn.

NOTE: LED (light-emitting diode) lights with a clear lens are acceptable, if of an approved type. For those vehicles that are Vehicles equipped with a multiple LED (light-emitting diode) light (not filament-burning bulbs), they will pass inspection if more than 50% of the diode lights are burning.

5. Two amber lamps are not mounted on the front and two red lamps on the rear, so as to indicate the extreme width of the body, and as high on the permanent body as practical, except that approved 180 degree lamps with yellow or amber lens may be mounted on the side of the vehicle at or as near the front as possible, or if the front is not the widest portion, the lamps may be installed on the side and as near that point as possible.

And with the further exception that 180 degree lamps with red lens may be mounted on the side of the vehicle at or as near the rear as possible or if the rear is not the widest portion of the vehicle, the lamps may be installed on the side as near that point as possible.

NOTE: Any vehicle equipped with three red identification lamps with the lamp centers spaced not less than six inches or more than 12 inches apart and installed as close as practicable to the top of the vehicle and as close as practicable to the vertical centerline of the vehicle may have the rear dimension or marker lamps required by subdivision 5 of this section mounted at any height but indicate as nearly as practicable the extreme width of the vehicle.

NOTE: Dump trucks with a high lift body, concrete mixer trucks and other specially constructed vehicles may be equipped with the required clearance lamps not mounted on the extreme rear, provided such red lamps are clearly visible from the rear and provided further that two red reflectors of an approved type are mounted on the extreme rear. In unusual cases the rear lamp may be mounted on the cab and another red reflex reflector placed on the extreme rear.

NOTE: In addition to the required clearance lamps showing to the front and to the rear, a vehicle may be equipped with side marker lamps on the side of the vehicle. When such an installation is used, all of the side marker lamps on the side except the one at or near the rear must have an amber lens. The side marker lamps on the side at or near the rear must have a red lens.

6. Any vehicle covered by subdivision 1 of this section, except school buses, is not equipped with amber reflectors on the sides as near the front as practical, and red reflectors on the rear. The reflectors must be at least 15 inches and not more than 60 inches from the ground. No reflector can have a piece broken from its reflective surface, but may have one or more cracks.

7. Any combination of vehicles whose actual length exceeds 35 feet if the vehicles are not wide enough to have clearance lights, if the vehicle is not equipped with reflex reflectors of a type approved by the superintendent and mounted on the widest part of the towed vehicle so as to be visible from the front and sides of the vehicle. No reflector can have a piece broken from its reflective surface, but may have one or more cracks.

8. Any passenger vehicle is equipped with clearance lamps, unless such lamps are used to mark the extreme width of the vehicle or used as taxicab identification, or used as supplemental turn signals. (See 19VAC30-70-190 B.)

NOTE: Vehicles so constructed as to make compliance with the requirements of subdivisions 1, 5, 7, and 9 of this section impractical, will be equipped with clearance lamps and reflectors at the most practical location to provide maximum visibility.

9. Any vehicle is not equipped with: two front side marker lights (amber), two rear side marker lights (red), and two rear reflectors (red).

 

Description: http://leg5.state.va.us/images/399362101007VSPRE_files/image001.gif

 

 

Description: http://leg5.state.va.us/images/399362101007VSPRE_files/image002.gif

 

 

Description: http://leg5.state.va.us/images/399611930209VSPRE_files/image001.gif

 

 

 

If equipped with three red identification lamps, the required clearance lamps may be mounted at any height so long as they indicate, as nearly as practicable, the extreme width of the vehicle.

Description: http://leg5.state.va.us/images/399611930209VSPRE_files/image002.gif

 

 

Description: http://leg5.state.va.us/images/399612203130VSPRE_files/image001.gif

Amber Reflector -- At least 15 inches but not more than 60 inches from the ground

 

 

Description: http://leg5.state.va.us/images/399612203130VSPRE_files/image002.gif

Red Reflectors -- At least 15 inches and not more than 60 inches from the ground

 

Description: http://leg5.state.va.us/images/403592177056LEGJDC_files/image001.jpg

19VAC30-70-580

19VAC30-70-580. Glass and glazing.

A. Motor vehicles may be inspected without windshields, side glasses, or any kind of glazing except that any motor vehicle other than a motorcycle that was manufactured, assembled, or reconstructed after July 1, 1970, must be equipped with a windshield. If glass or other glazing is installed, it must be inspected. If no windshield is installed, see 19VAC30-70-50, C, for location of the sticker.

B. Inspect for and reject if:

1. Any motor vehicle manufactured or assembled after January 1, 1936, or any bus or school bus manufactured or assembled after January 1, 1935, is not equipped throughout with safety glass, or other safety glazing material. (This requirement includes slide-in campers used on pickups or trucks, caps, or covers used on pickup trucks, motor homes, and vans.)

2. Any safety glass or glazing used in a motor vehicle is not of an approved type and properly identified (refer to approved equipment section). (Replacement safety glass installed in any part of a vehicle other than the windshield need not bear a trademark or name, provided the glass consists of two or more sheets of glass separated by a glazing material, and provided the glass is cut from a piece of approved safety glass, and provided the edge of the glass can be observed.)

3. Any glass at any location where glass is used is cracked or broken so that it is likely to cut or injure a person in the vehicle.

4. Windshield has any cloudiness more than three inches above the bottom, one inch inward from the outer borders, one inch down from the top, or one inch inward from the center strip. The bottom of the windshield shall be defined as the point where the top of the dash contacts the windshield.

5. Any distortion or obstruction that interferes with a driver's vision; any alteration has been made to a vehicle that obstructs the driver's clear view through the windshield. This may include large objects hanging from the inside mirror or mounted to the windshield, cell phone mounts, GPS devices, CB radios or tachometers mounted on the dash or windshield, hood scoops, and other ornamentation on or in front of the hood that is not transparent.

a. Any hood scoop installed on any motor vehicle manufactured for the year 1990 or earlier model year cannot exceed 2-1/4 inches high at its highest point measured from the junction of the dashboard and the windshield.

b. Any hood scoop installed on any motor vehicle manufactured for the year 1991 or subsequent model year cannot exceed 1-1/8 inches high at its highest point measured from the junction of the dashboard and the windshield.

NOTE: Antennas, transponders, and similar devices must not be mounted more than 152 mm (six inches) below the upper edge of the windshield. These devices must be located outside the area swept by the windshield wipers, and outside the driver's sight lines to the road and highway signs and signals.

NOTE: Vehicles 10,001 pounds (GVWR) or more, submitted for inspection, with a navigational device, video event recording device, or a crash avoidance camera mounted on the interior of the windshield, when the entire device is mounted not more than four inches below the upper edge of the area swept by the windshield wipers or any other location outside the area swept by the windshield wipers, shall be issued an approval sticker if no other violations are detected.

6. Windshield glass, on the driver's side, has any scratch more than 1/4 inch in width and six inches long within the area covered by the windshield wiper blade, excluding the three inches above the bottom of the windshield. A windshield wiper that remains parked within the driver's side windshield wiper area shall be rejected.

EXCEPTION: Do not reject safety grooves designed to clean wiper blades if the grooves do not extend upward from the bottom of the windshield more than six inches at the highest point.

7. There is a pit, chip, or star crack larger than 3/4 inch in diameter at any location in the windshield above the topmost portion of the steering wheel except the two-inch border at each side.

8. At any location above the topmost portion of the steering wheel excluding a two-inch border at the top and one-inch border at the sides there is:

a. Any crack over 1/4 inch in width.

b. Any crack 1/4 inch or less in width intersected by another crack.

c. Any damage area 3/4 inch or less in diameter if within three inches of any other damage area.

9. Any sticker is on the windshield other than an official one required by law, or permitted by the superintendent. Authorization is hereby granted for stickers or decals, to include those required by any county, town, or city, measuring not more than 2-1/2 inches in width and four inches in length to be placed in the blind spot behind the rear view mirror. The normal location for any required county, town, or city sticker or decal is adjacent to the right side of official inspection sticker when viewed from inside the vehicle. The top edge of the sticker is to be approximately four inches from the bottom of the windshield. The left side edge adjacent to the official inspection sticker shall not be more than 1/4-inch from the right edge of the official inspection sticker when viewed from inside the vehicle. Valid Commercial Vehicle Safety Alliance (CVSA) inspection decals, or similar commercial vehicle inspection decal issued by local law enforcement, may be placed at the bottom right corner of the windshield when viewed from inside the vehicle. The top edge of such decals are to be approximately four inches from the bottom of the windshield when viewed from inside the vehicle and are to be located outside the area swept by the windshield wipers.

Any sticker or decal required by the laws of any other state or the District of Columbia and displayed upon the windshield of a vehicle submitted for inspection in this state is permitted by the superintendent, provided the vehicle is currently registered in that jurisdiction and the sticker is displayed in a manner designated by the issuing authority and has not expired. This includes vehicles with dual registration, i.e., Virginia and the District of Columbia.

NOTE: Any Virginia registered vehicle displaying a valid sticker or decal required by a county, town, or city is permitted by the superintendent to remain in its current location through December 31, 2018, unless such location conflicts with the inspection sticker placement. This will afford localities time to enact changes to regulations governing required stickers or decals, which may be impacted by the 2018 inspection sticker placement change.

NOTE: Toll transponder devices may be affixed to the inside center of the windshield at the roof line just above the rear view mirror. If space does not allow, then it may be affixed to the immediate right of the mirror at the roof line.

NOTE: A licensed motor vehicle dealer may apply one transponder sticker no larger than one inch by four inches and one barcode sticker no larger than three inches by four inches to the driver's side edge of a vehicle's windshield to be removed upon the sale or lease of the vehicle provided that it does not extend below the AS-1 line. In the absence of an AS-1 line, the sticker cannot extend more than three inches downward from the top of the windshield.

NOTE: Any vehicle displaying an expired sticker or decal on its windshield at the time of inspection, excluding a rejection sticker, shall not be issued an approval sticker unless the owner or operator authorizes its removal. A rejection sticker will be issued versus an involuntary removal.

10. Sunshading material attached to the windshield extends more than three inches downward from the top of the windshield, unless authorized by the Virginia Department of Motor Vehicles and indicated on the vehicle registration.

NOTE: Sunshading material on the windshield displaying words, lettering, numbers or pictures that do not extend below the AS-1 line are permitted.

NOTE: Vehicles with logos made into the glass at the factory that meet federal standards will pass state inspection.

11. Any sunscreening material is scratched, distorted, wrinkled or obscures or distorts clear vision through the glazing.

12. Front side windows have cloudiness above three inches from the bottom of the glass, or other defects that affect the driver's vision or one or more cracks which permit one part of the glass to be moved in relation to another part. Wind silencers, breezes or other ventilator adaptors are not made of clear transparent material.

13. Glass in the left front door cannot be lowered so a hand signal can be given. (This does not apply to vehicle equipped with approved turn signals which were not designed or manufactured for left front glass to be lowered.) If either front door has the glass removed and material inserted in place of the glass which could obstruct the driver's vision.

Exception: Sunscreening material is permissible if the vehicle is equipped with a mirror on each side.

14. Any sticker or other obstruction is on either front side window, rear side windows, or rear windows. (The price label, fuel economy label and the buyer's guide required by federal statute and regulations to be affixed to new or used vehicles by the manufacturer shall normally be affixed to one of the rear side windows.) If a vehicle only has two door windows, the labels may be affixed to one of these windows. If a vehicle does not have any door or side windows, the labels may be temporarily affixed to the right side of the windshield until the vehicle is sold to the first purchaser.

NOTE: A single sticker no larger than 20 square inches in area, if such sticker is totally contained within the lower five inches of the glass in the rear window or a single sticker or decal no larger than 10 square inches located in an area not more than three inches above the bottom and not more than eight inches from the rearmost edge of either front side window, is permissible and should not be rejected.

Do not reject a tractor truck having a gross vehicle weight rating of 26,001 pounds or more equipped with one optically grooved clear plastic wide angle lens affixed to the right front side window. Such wide angle lens shall not extend upward from the bottom of the window opening more than six inches or backward from the front of the window opening more than eight inches.

15. Rear window is clouded or distorted so that the driver does not have a view 200 feet to the rear.

EXCEPTIONS: The following are permissible if the vehicle is equipped with a mirror on each side:

a. There is attached to one rear window of such motor vehicle one optically grooved clear plastic right angle rear view lens, not exceeding 18 inches in diameter in the case of a circular lens or not exceeding 11 inches by 14 inches in the case of a rectangular lens, which enables the operator of the motor vehicle to view below the line of sight as viewed through the rear window.

b. There is affixed to the rear side windows, rear window or windows of such motor vehicle any sticker or stickers, regardless of size.

c. There is affixed to the rear side windows, rear window or windows of such motor vehicle a single layer of sunshading material.

d. Rear side windows, rear window or windows is clouded or distorted.

19VAC30-70-630

19VAC30-70-630. Hood latch system; batteries.

A. "Hood" means any exterior movable body panel forward of the windshield that is used to cover an engine, luggage, storage or battery compartment.

B. Inspect for and reject if:

1. Each hood is not provided with a hood latch system that will securely hold the hood in its proper fully-closed position.

2. The latch release mechanism or its parts are broken, missing or badly adjusted so that the hood cannot be opened and closed properly.

3. Latching system on a vehicle equipped with a tilt cab is defective, broken, missing, or not properly adjusted so that the tilt cab is held securely when it is in its latched position.

C. Battery mounting and storage. Inspect for and reject if:

1. A battery is not securely attached to a fixed part of the motor vehicle or trailer. A battery is not protected by a removable cover or enclosure if the battery is installed in a location other than the engine compartment.

2. All brackets, hardware, bolts, and bushings used for securely mounting the battery to the vehicle are not present.

3. Removable covers or enclosures are not substantial and are not securely latched or fastened.

4. The battery compartment does not have openings to provide ample battery ventilation and drainage.

5. Whenever the cable to the starting motor passes through a metal compartment, the cable shall be protected against grounding by an acid and waterproof insulating bushing.

6. Whenever a battery and a fuel tank are both placed under the driver's seat, (i) the battery and fuel tank are not partitioned from each other or (ii) each compartment is not provided with an independent cover, ventilation, and drainage.

19VAC30-70-670

19VAC30-70-670. Muffler, exhaust system, and trailer venting.

A. Flexible tubing may be used anywhere in the exhaust system.

B. Inspection of exhaust system does not concern noise level.

C. Inspect for and reject if:

1. There is any leakage of exhaust gases at any point in the system. Do not reject "built-in" drain holes in muffler or tailpipe.

2. A muffler or catalytic converter has been repaired in any manner. The exhaust pipe may be welded to the muffler or catalytic converter. Holes or cracks in the exhaust line have been repaired with a patch or caulking.

3. Tailpipe opening is mashed or pinched.

4. Brackets are loose, broken, or missing.

5. Discharge of exhaust:

a. The exhaust system fails to discharge the exhaust to the rear or sides of that part of a property-carrying vehicle which is designed for and normally used for the driver and passengers, and to the rear or sides of the passenger and trunk compartment of passenger vehicles, unless such design is consistent with the original vehicle manufacturer exhaust system.

b. The exhaust system of a bus powered by a gasoline engine shall discharge to the atmosphere at or within six inches forward of the rearmost part of the bus.

EXCEPTION: Type I small forward control buses (14,000 GVWR Class) and cutaway model buses (10,000 GVWR or less) may discharge the exhaust behind the rear wheels.

c. The exhaust system of a bus powered by other than a gasoline engine shall discharge to the atmosphere either:

(1) At or within 15 inches forward of the rearmost part of the vehicle; or

(2) To the rear of all doors or windows designed to open, except windows designed to be opened solely as emergency exits.

6. Inspection of trailers and semitrailers will include a visual inspection of the venting of cooking or heating appliances to the outside of the trailer or semitrailer to determine if the heating and cooking appliances are adequately vented to the outside to prevent the asphyxiation of occupants of any trailer or semitrailer by the operation of the heating or cooking appliances.

a. Reject the trailer or semitrailer if not equipped with a vent or venting system to the outside.

b. Reject the trailer or semitrailer if there is any complete or partial obstruction of the vent or venting system.