9VAC5-20-21. Documents incorporated by reference.

A. The Administrative Process Act and Virginia Register Act provide that state regulations may incorporate documents by reference. Throughout these regulations, documents of the types specified below have been incorporated by reference.

1. United States Code.

2. Code of Virginia.

3. Code of Federal Regulations.

4. Federal Register.

5. Technical and scientific reference documents.

Additional information on key federal regulations and nonstatutory documents incorporated by reference and their availability may be found in subsection E of this section.

B. Any reference in these regulations to any provision of the Code of Federal Regulations (CFR) shall be considered as the adoption by reference of that provision. The specific version of the provision adopted by reference shall be that contained in the CFR (2010) (2012) in effect July 1, 2010 2012. In making reference to the Code of Federal Regulations, 40 CFR Part 35 means Part 35 of Title 40 of the Code of Federal Regulations; 40 CFR 35.20 means § 35.20 in Part 35 of Title 40 of the Code of Federal Regulations.

C. Failure to include in this section any document referenced in the regulations shall not invalidate the applicability of the referenced document.

D. Copies of materials incorporated by reference in this section may be examined by the public at the central office of the Department of Environmental Quality, Eighth Floor, 629 East Main Street, Richmond, Virginia, between 8:30 a.m. and 4:30 p.m. of each business day.

E. Information on federal regulations and nonstatutory documents incorporated by reference and their availability may be found below in this subsection.

1. Code of Federal Regulations.

a. The provisions specified below from the Code of Federal Regulations (CFR) are incorporated herein by reference.

(1) 40 CFR Part 50 -- National Primary and Secondary Ambient Air Quality Standards.

(a) Appendix A-1 -- Reference Measurement Principle and Calibration Procedure for the Measurement of Sulfur Dioxide in the Atmosphere (Ultraviolet Fluorescence Method).

(b) Appendix A-2 -- Reference Method for the Determination of Sulfur Dioxide in the Atmosphere (Pararosaniline Method).

(c) Appendix B -- Reference Method for the Determination of Suspended Particulate Matter in the Atmosphere (High-Volume Method).

(d) Appendix C -- Measurement Principle and Calibration Procedure for the Continuous Measurement of Carbon Monoxide in the Atmosphere (Non-Dispersive Infrared Photometry).

(e) Appendix D -- Measurement Principle and Calibration Procedure for the Measurement of Ozone in the Atmosphere.

(f) Appendix E -- Reserved.

(g) Appendix F -- Measurement Principle and Calibration Procedure for the Measurement of Nitrogen Dioxide in the Atmosphere (Gas Phase Chemiluminescence).

(h) Appendix G -- Reference Method for the Determination of Lead in Suspended Particulate Matter Collected from Ambient Air.

(i) Appendix H -- Interpretation of the National Ambient Air Quality Standards for Ozone.

(j) Appendix I -- Interpretation of the 8-Hour Primary and Secondary National Ambient Air Quality Standards for Ozone.

(k) Appendix J -- Reference Method for the Determination of Particulate Matter as PM₁₀ in the Atmosphere.

(l) Appendix K -- Interpretation of the National Ambient Air Quality Standards for Particulate Matter.

(m) Appendix L -- Reference Method for the Determination of Fine Particulate Matter as PM_2.5 in the Atmosphere.

(n) Appendix M -- Reserved.

(o) Appendix N -- Interpretation of the National Ambient Air Quality Standards for PM_2.5.

(p) Appendix O -- Reference Method for the Determination of Coarse Particulate Matter as PM in the Atmosphere.

(q) Appendix P -- Interpretation of the Primary and Secondary National Ambient Air Quality Standards for Ozone.

(r) Appendix Q -- Reference Method for the Determination of Lead in Suspended Particulate Matter as PM₁₀ Collected from Ambient Air.

(s) Appendix R -- Interpretation of the National Ambient Air Quality Standards for Lead.

(t) Appendix S -- Interpretation of the Primary National Ambient Air Quality Standards for Oxides of Nitrogen (Nitrogen Dioxide).

(u) Appendix T -- Interpretation of the Primary National Ambient Air Quality Standards for Oxides of Sulfur (Sulfur Dioxide).

(2) 40 CFR Part 51 -- Requirements for Preparation, Adoption, and Submittal of Implementation Plans.

(a) Appendix M -- Recommended Test Methods for State Implementation Plans.

(b) Appendix S -- Emission Offset Interpretive Ruling.

(c) Appendix W -- Guideline on Air Quality Models (Revised).

(d) Appendix Y -- Guidelines for BART Determinations Under the Regional Haze Rule.

(3) 40 CFR Part 55 -- Outer Continental Shelf Air Regulations.

(4) 40 CFR Part 58 -- Ambient Air Quality Surveillance.

Appendix A -- Quality Assurance Requirements for SLAMS, SPMs and PSD Air Monitoring.

(5) 40 CFR Part 59 -- National Volatile Organic Compound Emission Standards for Consumer and Commercial Products.

(a) Subpart C -- National Volatile Organic Compound Emission Standards for Consumer Products.

(b) Subpart D -- National Volatile Organic Compound Emission Standards for Architectural Coatings, Appendix A -- Determination of Volatile Matter Content of Methacrylate Multicomponent Coatings Used as Traffic Marking Coatings.

(6) 40 CFR Part 60 -- Standards of Performance for New Stationary Sources.

The specific provisions of 40 CFR Part 60 incorporated by reference are found in Article 5 (9VAC5-50-400 et seq.) of Part II of 9VAC5-50 (New and Modified Sources).

(7) 40 CFR Part 61 -- National Emission Standards for Hazardous Air Pollutants.

The specific provisions of 40 CFR Part 61 incorporated by reference are found in Article 1 (9VAC5-60-60 et seq.) of Part II of 9VAC5-60 (Hazardous Air Pollutant Sources).

(8) 40 CFR Part 63 -- National Emission Standards for Hazardous Air Pollutants for Source Categories.

The specific provisions of 40 CFR Part 63 incorporated by reference are found in Article 2 (9VAC5-60-90 et seq.) of Part II of 9VAC5-60 (Hazardous Air Pollutant Sources).

(9) 40 CFR Part 64 -- Compliance Assurance Monitoring.

(10) 40 CFR Part 72 -- Permits Regulation.

(11) 40 CFR Part 73 -- Sulfur Dioxide Allowance System.

(12) 40 CFR Part 74 -- Sulfur Dioxide Opt-Ins.

(13) 40 CFR Part 75 -- Continuous Emission Monitoring.

(14) 40 CFR Part 76 -- Acid Rain Nitrogen Oxides Emission Reduction Program.

(15) 40 CFR Part 77 -- Excess Emissions.

(16) 40 CFR Part 78 -- Appeal Procedures for Acid Rain Program.

(17) 40 CFR Part 152 Subpart I -- Classification of Pesticides.

(18) 49 CFR Part 172 -- Hazardous Materials Table. Special Provisions, Hazardous Materials Communications, Emergency Response Information, and Training Requirements, Subpart E, Labeling.

(19) 29 CFR Part 1926 Subpart F -- Fire Protection and Prevention.

b. Copies may be obtained from: Superintendent of Documents, P.O. Box 371954, Pittsburgh, Pennsylvania 15250-7954; phone (202) 783-3238.

2. U.S. Environmental Protection Agency.

a. The following documents from the U.S. Environmental Protection Agency are incorporated herein by reference:

(1) Reich Test, Atmospheric Emissions from Sulfuric Acid Manufacturing Processes, Public Health Service Publication No. PB82250721, 1980.

(2) Compilation of Air Pollutant Emission Factors (AP-42). Volume I: Stationary and Area Sources, stock number 055-000-00500-1, 1995; Supplement A, stock number 055-000-00551-6, 1996; Supplement B, stock number 055-000-00565, 1997; Supplement C, stock number 055-000-00587-7, 1997; Supplement D, 1998; Supplement E, 1999.

(3) "Guidelines for Determining Capture Efficiency" (GD-35), Emissions Monitoring and Analysis Division, Office of Air Quality Planning and Standards, January 9, 1995.

b. Copies of the document identified in subdivision E 2 a (1) of this subdivision, and Volume I and Supplements A through C of the document identified in subdivision E 2 a (2) of this subdivision, may be obtained from: U.S. Department of Commerce, National Technical Information Service, 5285 Port Royal Road, Springfield, Virginia 22161; phone 1-800-553-6847. Copies of Supplements D and E of the document identified in subdivision E 2 a (2) of this subdivision may be obtained online from EPA's Technology Transfer Network at http://www.epa.gov/ttn/index.html. Copies of the document identified in subdivision E 2 a (3) of this subdivision are only available online from EPA's Technology Transfer Network at http://www.epa.gov/ttn/emc/guidlnd.html.

3. U.S. government.

a. The following document from the U.S. government is incorporated herein by reference: Standard Industrial Classification Manual, 1987 (U.S. Government Printing Office stock number 041-001-00-314-2).

b. Copies may be obtained from: Superintendent of Documents, P.O. Box 371954, Pittsburgh, Pennsylvania 15250-7954; phone (202) 512-1800.

4. American Society for Testing and Materials (ASTM).

a. The documents specified below from the American Society for Testing and Materials are incorporated herein by reference.

(1) D323-99a, "Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method)."

(2) D97-96a, "Standard Test Method for Pour Point of Petroleum Products."

(3) D129-00, "Standard Test Method for Sulfur in Petroleum Products (General Bomb Method)."

(4) D388-99, "Standard Classification of Coals by Rank."

(5) D396-98, "Standard Specification for Fuel Oils."

(6) D975-98b, "Standard Specification for Diesel Fuel Oils."

(7) D1072-90(1999), "Standard Test Method for Total Sulfur in Fuel Gases."

(8) D1265-97, "Standard Practice for Sampling Liquefied Petroleum (LP) Gases (Manual Method)."

(9) D2622-98, "Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-Ray Fluorescence Spectrometry."

(10) D4057-95(2000), "Standard Practice for Manual Sampling of Petroleum and Petroleum Products."

(11) D4294-98, "Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy."

(12) D523-89, "Standard Test Method for Specular Gloss" (1999).

(13) D1613-02, "Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer and Related Products" (2002).

(14) D1640-95, "Standard Test Methods for Drying, Curing, or Film Formation of Organic Coatings at Room Temperature" (1999).

(15) E119-00a, "Standard Test Methods for Fire Tests of Building Construction Materials" (2000).

(16) E84-01, "Standard Test Method for Surface Burning Characteristics of Building Construction Materials" (2001).

(17) D4214-98, "Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films" (1998).

(18) D86-04b, "Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure" (2004).

(19) D4359-90, "Standard Test Method for Determining Whether a Material is a Liquid or a Solid" (reapproved 2000).

(20) E260-96, "Standard Practice for Packed Column Gas Chromatography" (reapproved 2001).

(21) D3912-95, "Standard Test Method for Chemical Resistance of Coatings Used in Light-Water Nuclear Power Plants" (reapproved 2001).

(22) D4082-02, "Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants."

(23) F852-99, "Standard Specification for Portable Gasoline Containers for Consumer Use" (reapproved 2006).

(24) F976-02, "Standard Specification for Portable Kerosine and Diesel Containers for Consumer Use."

(25) D4457-02, "Standard Test Method for Determination of Dichloromethane and 1,1,1-Trichloroethane in Paints and Coatings by Direct Injection into a Gas Chromatograph" (reapproved 2008).

(26) D3792-05, "Standard Test Method for Water Content of Coatings by Direct Injection Into a Gas Chromatograph."

(27) D2879-97, "Standard Test Method for Vapor Pressure-Temperature Relationship and Initial Decomposition Temperature of Liquids by Isoteniscope" (reapproved 2007).

b. Copies may be obtained from: American Society for Testing Materials, 100 Barr Harbor Drive, West Conshohocken, Pennsylvania 19428-2959; phone (610) 832-9585.

5. American Petroleum Institute (API).

a. The following document from the American Petroleum Institute is incorporated herein by reference: Evaporative Loss from Floating Roof Tanks, API MPMS Chapter 19, April 1, 1997.

b. Copies may be obtained from: American Petroleum Institute, 1220 L Street, Northwest, Washington, D.C. 20005; phone (202) 682-8000.

6. American Conference of Governmental Industrial Hygienists (ACGIH).

a. The following document from the ACGIH is incorporated herein by reference: 1991-1992 Threshold Limit Values for Chemical Substances and Physical Agents and Biological Exposure Indices (ACGIH Handbook).

b. Copies may be obtained from: ACGIH, 1330 Kemper Meadow Drive, Suite 600, Cincinnati, Ohio 45240; phone (513) 742-2020.

7. National Fire Prevention Association (NFPA).

a. The documents specified below from the National Fire Prevention Association are incorporated herein by reference.

(1) NFPA 385, Standard for Tank Vehicles for Flammable and Combustible Liquids, 2000 Edition.

(2) NFPA 30, Flammable and Combustible Liquids Code, 2000 Edition.

(3) NFPA 30A, Code for Motor Fuel Dispensing Facilities and Repair Garages, 2000 Edition.

b. Copies may be obtained from the National Fire Prevention Association, One Batterymarch Park, P.O. Box 9101, Quincy, Massachusetts 02269-9101; phone (617) 770-3000.

8. American Society of Mechanical Engineers (ASME).

a. The documents specified below from the American Society of Mechanical Engineers are incorporated herein by reference.

(1) ASME Power Test Codes: Test Code for Steam Generating Units, Power Test Code 4.1-1964 (R1991).

(2) ASME Interim Supplement 19.5 on Instruments and Apparatus: Application, Part II of Fluid Meters, 6th edition (1971).

(3) Standard for the Qualification and Certification of Resource Recovery Facility Operators, ASME QRO-1-1994.

b. Copies may be obtained from the American Society of Mechanical Engineers, Three Park Avenue, New York, New York 10016; phone (800) 843-2763.

9. American Hospital Association (AHA).

a. The following document from the American Hospital Association is incorporated herein by reference: An Ounce of Prevention: Waste Reduction Strategies for Health Care Facilities, AHA Catalog no. W5-057007, 1993.

b. Copies may be obtained from: American Hospital Association, One North Franklin, Chicago, IL 60606; phone (800) 242-2626.

10. Bay Area Air Quality Management District (BAAQMD).

a. The following documents from the Bay Area Air Quality Management District are incorporated herein by reference:

(1) Method 41, "Determination of Volatile Organic Compounds in Solvent-Based Coatings and Related Materials Containing Parachlorobenzotrifluoride" (December 20, 1995).

(2) Method 43, "Determination of Volatile Methylsiloxanes in Solvent-Based Coatings, Inks, and Related Materials" (November 6, 1996).

b. Copies may be obtained from: Bay Area Air Quality Management District, 939 Ellis Street, San Francisco, CA 94109, phone (415) 771-6000.

11. South Coast Air Quality Management District (SCAQMD).

a. The following documents from the South Coast Air Quality Management District are incorporated herein by reference:

(1) Method 303-91, "Determination of Exempt Compounds," in Manual SSMLLABM, "Laboratory Methods of Analysis for Enforcement Samples" (1996).

(2) Method 318-95, "Determination of Weight Percent Elemental Metal in Coatings by X-Ray Diffraction," in Manual SSMLLABM, "Laboratory Methods of Analysis for Enforcement Samples" (1996).

(3) Rule 1174 Ignition Method Compliance Certification Protocol (February 28, 1991).

(4) Method 304-91, "Determination of Volatile Organic Compounds (VOC) in Various Materials," in Manual SSMLLABM, "Laboratory Methods of Analysis for Enforcement Samples" (1996).

(5) Method 316A-92, "Determination of Volatile Organic Compounds (VOC) in Materials Used for Pipes and Fittings" in Manual SSMLLABM, "Laboratory Methods of Analysis for Enforcement Samples" (1996).

(6) "General Test Method for Determining Solvent Losses from Spray Gun Cleaning Systems," October 3, 1989.

b. Copies may be obtained from: South Coast Air Quality Management District, 21865 E. Copley Drive, Diamond Bar, CA 91765, phone (909) 396-2000.

12. California Air Resources Board (CARB).

a. The following documents from the California Air Resources Board are incorporated herein by reference:

(1) Test Method 510, "Automatic Shut-Off Test Procedure for Spill-Proof Systems and Spill-Proof Spouts" (July 6, 2000).

(2) Test Method 511, "Automatic Closure Test Procedure for Spill-Proof Systems and Spill-Proof Spouts" (July 6, 2000).

(3) Method 100, "Procedures for Continuous Gaseous Emission Stack Sampling" (July 28, 1997).

(4) Test Method 513, "Determination of Permeation Rate for Spill-Proof Systems" (July 6, 2000).

(5) Method 310, "Determination of Volatile Organic Compounds (VOC) in Consumer Products and Reactive Organic Compounds in Aerosol Coating Products (Including Appendices A and B)" (May 5, 2005).

(6) California Code of Regulations, Title 17, Division 3, Chapter 1, Subchapter 8.5, Article 1, § 94503.5 (2003).

(7) California Code of Regulations, Title 17, Division 3, Chapter 1, Subchapter 8.5, Article 2, §§ 94509 and 94511 (2003).

(8) California Code of Regulations, Title 17, Division 3, Chapter 1, Subchapter 8.5, Article 4, §§ 94540-94555 (2003).

(9) "Certification Procedure 501 for Portable Fuel Containers and Spill-Proof Spouts, CP-501" (July 26, 2006).

(10) "Test Procedure for Determining Integrity of Spill-Proof Spouts and Spill-Proof Systems, TP-501" (July 26, 2006).

(11) "Test Procedure for Determining Diurnal Emissions from Portable Fuel Containers, TP-502" (July 26, 2006).

b. Copies may be obtained from: California Air Resources Board, P.O. Box 2815, Sacramento, CA 95812, phone (906) 322-3260 or (906) 322-2990.

13. American Architectural Manufacturers Association.

a. The following documents from the American Architectural Manufacturers Association are incorporated herein by reference:

(1) Voluntary Specification 2604-02, "Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and Panels" (2002).

(2) Voluntary Specification 2605-02, "Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels" (2002).

b. Copies may be obtained from: American Architectural Manufacturers Association, 1827 Walden Office Square, Suite 550, Schaumburg, IL 60173, phone (847) 303-5664.

14. American Furniture Manufacturers Association.

a. The following document from the American Furniture Manufacturers Association is incorporated herein by reference: Joint Industry Fabrics Standards Committee, Woven and Knit Residential Upholstery Fabric Standards and Guidelines (January 2001).

b. Copies may be obtained from: American Furniture Manufacturers Association, P.O. Box HP-7, High Point, NC 27261; phone (336) 884-5000.

Article 55
Emission Standards for Sewage Sludge Incineration Units (Rule 4-55)

9VAC5-40-8200. Applicability and designation of affected facility.

A. The affected facilities to which the provisions of this article apply are sewage sludge incineration (SSI) units that meet all of the following criteria:

1. SSI units that commenced construction on or before October 14, 2010.

2. SSI units that meet the definition of a SSI unit as defined in 9VAC5-40-8210.

3. SSI units not exempt under subsection D of this section.

B. The provisions of this article apply throughout the Commonwealth of Virginia.

C. The following provisions govern changes to SSI units.

1. If the owner of a SSI unit makes changes that meet the definition of modification after September 21, 2011, the SSI unit becomes subject to Subpart LLLL of 40 CFR Part 60 and the provisions of this article no longer apply to that unit.

2. If the owner of a SSI unit makes physical or operational changes to a SSI unit for which construction commenced on or before September 21, 2011, primarily to comply with the provisions of this article, Subpart LLLL of 40 CFR Part 60 does not apply to that unit. Such changes do not qualify as modifications under Subpart LLLL of 40 CFR Part 60.

D. Exempt from the provisions of this article are combustion units that incinerate sewage sludge and are not located at a wastewater treatment facility designed to treat domestic sewage sludge. These units may be subject to 40 CFR Part 60 (e.g., Subpart CCCC of 40 CFR Part 60). The owner of such a combustion unit shall notify the board of an exemption claim under this subsection.

E. The provisions of 40 CFR Part 60 (other than Subpart MMMM of 40 CFR Part 60) cited in this article are applicable only to the extent that they are incorporated by reference in Article 5 (9VAC5-50-400 et seq.) of Part II of 9VAC5-50 (New and Modified Stationary Sources).

F. The provisions of Subpart MMMM (Emission Guidelines and Compliance Times for Existing Sewage Sludge Incineration Units) of 40 CFR Part 60 cited in this article are applicable only to the extent that they are incorporated by reference in 9VAC5-40-8370.

9VAC5-40-8210. Definitions.

A. For the purpose of applying this article in the context of the Regulations for the Control and Abatement of Air Pollution and related uses, the words or terms shall have the meanings given them in subsection C of this section.

B. As used in this article, all terms not defined herein shall have the meanings given them in 9VAC5-10 (General Definitions), unless otherwise required by context.

C. Terms shall have the meanings given them in 40 CFR 60.5250, except for the following:

"Administrator" means the board.

"Performance test," as defined in 40 CFR 63.2, means the collection of data resulting from the execution of a test method (usually three emission test runs) used to demonstrate compliance with a relevant emission standard as specified in the performance test section of the relevant standard.

"Table 1" means 9VAC5-40-8280 A and B.

"You" means the owner of an affected SSI unit.

9VAC5-40-8220. Emission limits and emission standards.

A. No owner or other person shall cause or permit to be discharged into the atmosphere from any SSI unit any emissions in excess of that allowed under subsection B of this section.

B. The provisions of 40 CFR 60.5165 apply.

9VAC5-40-8230. Standard for visible emissions.

The provisions of Article 1 (9VAC5-40-60 et seq.) of 9VAC5-40 (Emission Standards for Visible Emissions and Fugitive Dust/Emissions, Rule 4-1) apply, with the exception of 9VAC5-40-90 (Standard for fugitive dust/emissions).

9VAC5-40-8240. Standard for fugitive dust/emissions.

A. The provisions of Article 1 (9VAC5-40-60 et seq.) of 9VAC5-40 (Emission Standards for Visible Emissions and Fugitive Dust/Emissions, Rule 4-1) apply, with the exception of 9VAC5-40-80 (Standard for visible emissions), 9VAC5-40-100 (Monitoring), 9VAC5-40-110 (Test methods and procedures), and 9VAC5-40-120 (Waivers).

B. No owner or other person shall cause or permit to be discharged into the atmosphere from any ash conveying system (including conveyor transfer points) any visible emissions for more than 5.0% of hourly observation period, measured at three, one-hour observation periods.

9VAC5-40-8250. Standard for odor.

The provisions of Article 2 (9VAC5-40-130 et seq.) of 9VAC5-40 (Emissions Standards for Odor, Rule 4-2) apply.

9VAC5-40-8260. Standard for toxic pollutants.

The provisions of Article 4 (9VAC5-60-200 et seq.) of 9VAC5-60 (Emissions Standards for Toxic Pollutants from Existing Sources, Rule 6-4) apply.

9VAC5-40-8270. Operator training and certification.

A. The provisions of 40 CFR 60.5130, 40 CFR 60.5135, 40 CFR 60.5140, 40 CFR 60.5145, 40 CFR 60.5150, 40 CFR 60.5155, and 40 CFR 60.5160 apply.

B. The requirements of this section with regard to scheduling and obtaining certification through a program approved by the board may be met by obtaining a license from the Board for Waste Management Facility Operators. All training and licensing shall be conducted in accordance with Chapter 22.1 (§ 54.1-2209 et seq.) of Title 54.1 of the Code of Virginia and with 18VAC155-20 (Waste Management Facility Operators Regulations).

C. No owner of an affected facility shall allow the facility to be operated at any time unless a person is on duty who is responsible for the proper operation of the facility and has a license from the Board for Waste Management Facility operators in the correct classification. No provision of this article shall relieve any owner from the responsibility to comply in all respects with the requirements of Chapter 22.1 (§ 54.1-2209 et seq.) of Title 54.1 of the Code of Virginia and with 18VAC155-20 (Waste Management Facility Operators Regulations).

9VAC5-40-8280. Compliance schedule.

A. SSI units shall achieve final compliance or cease operation as expeditiously as practicable but not later than March 21, 2016.

B. The owner shall submit a final control plan no later than March 21, 2013.

C. The provisions of 40 CFR 60.5085, 40 CFR 60.5090, 40 CFR 60.5095, 40 CFR 60.5100, 40 CFR 60.5105, 40 CFR 60.5110, 40 CFR 60.5115, 40 CFR 60.5120, and 40 CFR 60.5125 apply.

9VAC5-40-8290. Operating requirements.

A. No owner or other person shall operate any SSI unit in a manner that does not comply with the provisions of subsection B of this section.

B. The provisions of 40 CFR 60.5170 and 40 CFR 60.5175 apply.

9VAC5-40-8300. Compliance.

A. With regard to the emissions standards in 9VAC5-40-8240 A, 9VAC5-40-8250, and 9VAC5-40-8260, the provisions of 9VAC5-40-20 (Compliance) apply.

B. With regard to the emission limits in 9VAC5-40-8220, 9VAC5-40-8240 B, and 9VAC5-40-8290, the following provisions apply:

1. 9VAC5-40-20 B, C, D, and E;

2. To the extent specified in the federal regulations cited in subdivision 3 of this subsection, 40 CFR 60.7, 40 CFR 60.8, 40 CFR 60.11, and 40 CFR 60.13; and

3. 40 CFR 60.5185, 40 CFR 60.5190, 40 CFR 60.5195, 40 CFR 60.5200, 40 CFR 60.5205, 40 CFR 60.5210, and 40 CFR 60.5215.

9VAC5-40-8310. Performance testing, monitoring, and calibration requirements.

A. With regard to the emissions standards in 9VAC5-40-8240 A, 9VAC5-40-8250, and 9VAC5-40-8260, the provisions of 9VAC5-40-30 (Emission testing) and 9VAC5-40-40 (Monitoring) apply.

B. With regard to the emission limits in 9VAC5-40-8220, 9VAC5-40-8240 B, and 9VAC5-40-8290, the following provisions apply:

1. 9VAC5-40-30 D and G;

2. 9VAC5-40-40 A and F;

3. 40 CFR 60.8(b) through (f), with the exception of paragraph (a);

4. 40 CFR 60.13; and

5. 40 CFR 60.5220 and 40 CFR 60.5225.

9VAC5-40-8320. Recordkeeping and reporting.

A. With regard to the emissions standards in 9VAC5-40-8240 A, 9VAC5-40-8250, and 9VAC5-40-8260, the provisions of 9VAC5-40-50 (Notification, records and reporting) apply.

B. With regard to the emission limits in 9VAC5-40-8220, 9VAC5-40-8240 B, and 9VAC5-40-8290, the following provisions apply:

1. 9VAC5-40-50 F and H;

2. 40 CFR 60.7; and

3. 40 CFR 60.5230 and 40 CFR 60.5235.

9VAC5-40-8330. Registration.

The provisions of 9VAC5-20-160 (Registration) apply.

9VAC5-40-8340. Facility and control equipment maintenance or malfunction.

A. With regard to the emissions standards in 9VAC5-40-8240 A, 9VAC5-40-8250, and 9VAC5-40-8260, the provisions of 9VAC5-20-180 (Facility and control equipment maintenance or malfunction) apply.

B. With regard to the emission limits in 9VAC5-40-8220, 9VAC5-40-8240 B, and 9VAC5-40-8290, the following provisions apply:

1. 9VAC5-20-180 with the exception of subsections E, F, and G; and

2. 40 CFR 60.5180 and 40 CFR 60.5181.

9VAC5-40-8350. Federal (Title V) operating permits.

A. The provisions of 40 CFR 60.5240 and 40 CFR 60.5245 apply.

B. Owners to which this section applies should contact the appropriate regional office for guidance on applying for a federal (Title V) operating permit.

9VAC5-40-8360. Other permits.

A permit may be required prior to beginning any of the activities specified below if the provisions of 9VAC5-50 (New and Modified Stationary Sources) and 9VAC5-80 (Permits for Stationary Sources) apply. Owners contemplating such action should review those provisions and contact the appropriate regional office for guidance on whether those provisions apply.

1. Construction of a facility.

2. Reconstruction (replacement of more than half) of a facility.

3. Modification (any physical change to equipment) of a facility.

4. Relocation of a facility.

5. Reactivation (re-startup) of a facility.

6. Operation of a facility.

9VAC5-40-8370. Documents incorporated by reference.

A. The United States Environmental Protection Agency (EPA) regulations promulgated at Subpart MMMM (Emission Guidelines and Compliance Times for Existing Sewage Sludge Incineration Units) of 40 CFR Part 60 and designated in subsection B of this section are incorporated by reference into this article. The 40 CFR section numbers appearing in subsection B of this section identify the specific provisions incorporated by reference. The specific version of the provisions incorporated by reference shall be that contained in the CFR in effect as specified in 9VAC5-20-21 B.

B. The following documents from the United States Environmental Protection Agency are incorporated herein by reference:

Model Rule, Increments of Progress

40 CFR 60.5085, What are my requirements for meeting increments of progress and achieving final compliance?

40 CFR 60.5090, When must I complete each increment of progress?

40 CFR 60.5095, What must I include in the notifications of achievement of increments of progress?

40 CFR 60.5100, When must I submit the notifications of achievement of increments of progress?

40 CFR 60.5105, What if I do not meet an increment of progress?

40 CFR 60.5110, How do I comply with the increment of progress for submittal of a control plan?

40 CFR 60.5115, How do I comply with the increment of progress for achieving final compliance?

40 CFR 60.5120, What must I do if I close my SSI unit and then restart it?

40 CFR 60.5125, What must I do if I plan to permanently close my SSI unit and not restart it?

Model Rule, Operator Training and Qualification

40 CFR 60.5130, What are the operator training and qualification requirements?

40 CFR 60.5135, When must the operator training course be completed?

40 CFR 60.5140, How do I obtain my operator qualification?

40 CFR 60.5145, How do I maintain my operator qualification?

40 CFR 60.5150, How do I renew my lapsed operator qualification?

40 CFR 60.5155, What if all the qualified operators are temporarily not accessible?

40 CFR 60.5160, What site-specific documentation is required and how often must it be reviewed by qualified SSI operators and other plant personnel who may operate the unit according to the provisions of 40 CFR 60.5155(a)?

Model Rule, Emission Limits, Emission Standards, and Operating Limits and Requirements

40 CFR 60.5165, What emission limits and standards must I meet and by when?

40 CFR 60.5170, What operating limits and requirements must I meet and by when?

40 CFR 60.5175, How do I establish operating limits if I do not use a wet scrubber, fabric filter, electrostatic precipitator, activated carbon injection, or afterburner, or if I limit emissions in some other manner, to comply with the emission limits?

40 CFR 60.5180, Do the emission limits, emission standards, and operating limits apply during periods of startup, shutdown, and malfunction?

40 CFR 60.5181, How do I establish affirmative defense for exceedance of an emission limit or standard during malfunction?

Model Rule, Initial Compliance Requirements

40 CFR 60.5185, How and when do I demonstrate initial compliance with the emission limits and standards?

40 CFR 60.5190, How do I establish my operating limits?

40 CFR 60.5195, By what date must I conduct the initial air pollution control device inspection and make any necessary repairs?

40 CFR 60.5200, How do I develop a site-specific monitoring plan for my continuous monitoring systems, bag leak detection system, and ash handling system, and by what date must I conduct an initial performance evaluation of my continuous monitoring systems and bag leak detection system?

Model Rule, Continuous Compliance Requirements

40 CFR 60.5205, How and when do I demonstrate continuous compliance with the emission limits and standards?

40 CFR 60.5210, How do I demonstrate continuous compliance with my operating limits?

40 CFR 60.5215, By what date must I conduct annual air pollution control device inspections and make any necessary repairs?

Model Rule, Performance Testing, Monitoring, and Calibration Requirements

40 CFR 60.5220, What are the performance testing, monitoring, and calibration requirements for compliance with the emission limits and standards?

40 CFR 60.5225, What are the monitoring and calibration requirements for compliance with my operating limits?

Model Rule, Recordkeeping and Reporting

40 CFR 60.5230, What records must I keep?

40 CFR 60.5235, What reports must I submit?

Model Rule, Title V Operating Permits

40 CFR 60.5240, Am I required to apply for and obtain a Title V operating permit for my existing SSI unit?

40 CFR 60.5245, When must I submit a Title V permit application for my existing SSI unit?

Model Rule, Definitions

40 CFR 60.5250, What definitions must I know?

TABLES

Table 2 to Subpart MMMM of 40 CFR Part 60, Model Rule, Emission Limits and Standards for Existing Fluidized Bed Sewage Sludge Incineration Units.

Table 3 to Subpart MMMM of 40 CFR Part 60, Model Rule, Emission Limits and Standards for Existing Multiple Hearth Sewage Sludge Incineration Units.

Table 4 to Subpart MMMM of 40 CFR Part 60, Model Rule, Operating Parameters for Existing Sewage Sludge Incineration Units.

Table 5 to Subpart MMMM of 40 CFR Part 60, Model Rule, Toxic Equivalency Factors.

Table 6 to Subpart MMMM of 40 CFR Part 60, Model Rule, Summary of Reporting Requirements for Existing Sewage Sludge Incineration Units.